Advanced Host Controller Interface

The Advanced Host Controller Interface (AHCI) is a technical standard defined by Intel that specifies the register-level interface of Serial ATA (SATA) host controllers in a non-implementation-specific manner in its motherboard chipsets.

The specification describes a system memory structure for computer hardware vendors to exchange data between host system memory and attached storage devices. AHCI gives software developers and hardware designers a standard method for detecting, configuring, and programming SATA/AHCI adapters. AHCI is separate from the SATA 3 Gbit/s standard, although it exposes SATA's advanced capabilities (such as hot swapping and native command queuing) such that host systems can utilize them. For modern solid state drives, the interface has been superseded by NVMe.

The current version of the specification is 1.3.1.

Operating modes
Many SATA controllers offer selectable modes of operation: legacy Parallel ATA emulation (more commonly called IDE Mode), standard AHCI mode (also known as Native Mode), or vendor-specific RAID (which generally enables AHCI in order to take advantage of its capabilities). Intel recommends choosing RAID mode on their motherboards (which also enables AHCI) rather than AHCI/SATA mode for maximum flexibility. Legacy mode is a software backward-compatibility mechanism intended to allow the SATA controller to run in legacy operating systems which are not SATA-aware or where a driver does not exist to make the operating system SATA-aware.

When a SATA controller is configured to operate in IDE Mode, the number of storage devices per controller is usually limited to four (two IDE channels, master device and slave device with up to two devices per channel), compared to the maximum of 32 devices/ports when configured in AHCI mode. But the chipset SATA interfaces may emulate more than one "IDE controller" when configured in IDE Mode.

Operating system support
AHCI is supported out of the box on Windows Vista and later, Linux-based operating systems (since version 2.6.19 of the kernel), OpenBSD (since version 4.1), NetBSD (since version 4.0), FreeBSD (since version 8.0), macOS, GNU Mach, ArcaOS, eComStation (since version 2.1), and Solaris 10 (since version 8/07). DragonFlyBSD based its AHCI implementation on OpenBSD's and added extended features such as port multiplier support. Older versions of operating systems require hardware-specific drivers in order to support AHCI. Windows XP and older do not provide AHCI support out of the box.

System drive boot issues
Some operating systems, notably Windows Vista, Windows 7, Windows 8, Windows 8.1 and Windows 10, do not configure themselves to load the AHCI driver upon boot if the SATA controller was not in AHCI mode at the time the operating system was installed. Although this is an easily rectifiable condition, it remains an ongoing issue with the AHCI standard.

The most prevalent symptom for an operating system (or systems) that are installed in IDE mode (in some BIOS firmware implementations otherwise called 'Combined IDE mode'), is that the system drive typically fails to boot, with an ensuing error message, if the SATA controller (in BIOS) is inadvertently switched to AHCI mode after OS installation. In Microsoft Windows the symptom is a boot loop which begins with a Blue Screen error, if not rectified.

Technically speaking, this is an implementation bug with AHCI that can be avoided, but it has not been fixed yet. As an interim resolution, Intel recommends changing the drive controller to AHCI or RAID before installing an operating system. (It may also be necessary to load chipset-specific AHCI or RAID drivers at installation time, for example from a USB flash drive).

On Windows Vista and Windows 7, this can be fixed by configuring the  device driver to start at boot time (rather than on-demand). Setting non-AHCI mode (i.e. IDE or Combined mode) in the BIOS will allow the user to boot into Windows, and thereby the required registry change can be performed. Consequently, the user then has the option of continuing to use the system in Combined mode or switching to AHCI mode. Inter alia with Windows 10 and 8, this can be fixed by forcing the correct drivers to reload during Safe Mode.

In Windows 8, Windows 8.1 and Windows Server 2012, the controller driver has changed from  to , and the procedures to upgrade to the AHCI controller is similar to that of Windows 7. On Windows 8, 8.1 and Windows Server 2012, changing from IDE mode to AHCI mode without first updating the registry will make the boot drive inaccessible (i.e. resulting in a recurring boot loop, which begins with a Blue Screen error).

In Windows 10, after changing the controller to AHCI mode, if the OS is allowed to reboot a couple of times after the start of the boot loop, which starts with an INACCESSIBLE_BOOT_DEVICE BSOD, Windows presents recovery options. Out of the Advanced options, if Startup Repair option is selected, Windows attempts to fix the issue and the PC begins to function normally.

A similar problem can occur on Linux systems if the AHCI driver is compiled as a kernel module rather than built into the kernel image, as it may not be included in the initrd (initial RAM disk) created when the controller is configured to run in Legacy Mode. The solution is either to build a new initrd containing the AHCI module, or to build the AHCI driver into the kernel image.

Power management
Power management is handled by the Aggressive Link Power Management (ALPM) protocol.