Closed-loop geothermal

Closed-loop geothermal systems (also known as “advanced geothermal systems” or “AGS”) are a type of engineered geothermal energy system containing subsurface working fluid that is heated in a hot rock reservoir without direct contact with rock pores and fractures.: Instead, the subsurface working fluid stays inside a closed loop of deeply buried pipes that conduct Earth’s heat. Closed-loop geothermal systems are one of the prominent categories of next-generation geothermal systems in development today. Like all geothermal systems, closed-loop geothermal systems provide renewable energy, and primarily operate as baseload resources that produce energy at a constant rate. Unlike conventional geothermal energy plants, closed-loop geothermal plants can be placed anywhere in the world, depending only on the depth of the hot rock resource.

Closed-loop geothermal projects are under development in the United States, Canada, Japan, and Germany.

Technology
Closed-loop geothermal companies use a wide variety of engineered systems to produce geothermal energy. These systems primarily vary based on the length and geometry of the closed-loop wells placed subsurface, but can also vary in the materials used in well construction and the working fluid used.

Two commons designs of closed-loop geothermal systems are the U-tube and the tube-in-tube:


 * U-tube closed-loop geothermal: In this system, cool water is pumped down one deep vertical pipe, which then extends horizontally for a certain distance at a depth where the rock is hot and then comes up in a different location. The horizontal section may be composed of one or multiple lateral (horizontal) well sections.
 * Tube-in-a-tube closed-loop geothermal: In this system, the cool water is pumped down along the outer layer of a pipe to a certain depth, at which point the pipe may extend an additional horizontal distance at that depth. When the hot water hits the end of the pipe it is pushed into the inner pipe, through which the hot water returns to the surface. Also called a coaxial or pipe-in-pipe system.

Research and development
Several closed-loop geothermal systems have been demonstrated globally. One commercial closed-loop geothermal project is under construction in Geretsried, Germany.

Advantages
The advantages of a deep, closed-loop geothermal circuit include


 * 1) No need for a geofluid
 * 2) No need for the hot rock to be permeable or porous
 * 3) All the introduced working fluid can be recirculated with zero loss
 * 4) No fracking or stimulation is required to establish the engineered geothermal reservoir.

These advantages mean closed-loop geothermal systems can be placed anywhere in the world as a source of carbon-free, baseload energy, with no impact to natural water resources and significantly reduced risk of induced seismicity.

Hot dry rock
Hot dry rock (HDR) is an abundant source of geothermal energy, but it is typically difficult to access. Hot, dry crystalline basement rocks are found almost everywhere sufficiently far beneath the surface. Multiple deep hot dry rock wells have been drilled around the world, including the US, Japan, Australia, France, and the UK. Whereas hydrothermal energy production can exploit already present hot fluids, HDR recovers heat from dry rock via the circulation of an artificially introduced working fluid. Ongoing efforts are underway to further develop and test technologies that can produce geothermal energy from hot dry rock, including Enhanced Geothermal Systems and Closed-Loop Geothermal Systems.

Closed-loop geothermal systems vs. ground source heat pumps
Closed-loop geothermal systems are not to be confused with the ground source heat pumps used for small-scale, largely residential heating and cooling. While both systems use underground closed-loop circuits of working fluid, there are important differences in the depth, temperature, scale, and applications for each system:


 * Depth: Ground source heat pumps are placed at shallow depths, less than 400 feet (122 meters). Closed-loop geothermal systems are drilled much deeper, greater than 1640 feet (500 meters), to access the hotter rock found at greater depths (see: geothermal gradient).
 * Temperature: Ground source heat pumps target shallow ground temperatures, which vary seasonally from 45 °F (7 °C) to 75 °F (21 °C). Closed-loop geothermal systems target much hotter underground temperatures, greater than 212 °F (100 °C), to produce larger volumes of energy.
 * Scale: Ground source heat pumps are used for small-scale residential heating and cooling and typically produce less than 1 kilowatt of thermal energy. Closed-Loop Geothermal Systems are used for utility-scale commercial and industrial energy production and typically produce greater than 1 megawatt of thermal energy.
 * Application: Ground source heat pumps are most often used for small-scale residential and commercial buildings, and are only used for heating and cooling applications. Closed-loop geothermal systems are most suitable for large-scale commercial and industrial use, and can be used for electricity production, in addition to 'direct use' heating and cooling.

See the glossary of geothermal heating and cooling page for further clarification.