Pressure swing adsorption

Pressure swing adsorption (PSA) is a technique used to separate some gas species from a mixture of gases (typically air) under pressure according to the species' molecular characteristics and affinity for an adsorbent material. It operates at near-ambient temperature and significantly differs from the cryogenic distillation commonly used to separate gases. Selective adsorbent materials (e.g., zeolites, (aka molecular sieves), activated carbon, etc.) are used as trapping material, preferentially adsorbing the target gas species at high pressure. The process then swings to low pressure to desorb the adsorbed gas.

Process
pressure_swing_adsorption_principle.svg is passed under pressure through a vessel containing an adsorbent bed of zeolite that attracts nitrogen more strongly than oxygen, a fraction of nitrogen will stay in the bed, and the gas exiting the vessel will be richer in oxygen than the mixture entering. When the bed reaches the limit of its capacity to adsorb nitrogen, it can be regenerated by decreasing the pressure, thus releasing the adsorbed nitrogen. It is then ready for another cycle of producing oxygen-enriched air.

Using two adsorbent vessels allows for near-continuous production of the target gas. It also allows a pressure equalisation, where the gas leaving the vessel being depressurised is used to partially pressurise the second vessel. This results in significant energy savings, and is a common industrial practice.

Adsorbents
Aside from their ability to discriminate between different gases, adsorbents for PSA systems are usually very porous materials chosen because of their large specific surface areas. Typical adsorbents are zeolite, activated carbon, silica gel, alumina, or synthetic resins. Though the gas adsorbed on these surfaces may consist of a layer only one or at most a few molecules thickness, surface areas of several hundred square meters per gram enable the adsorption of a large portion of the adsorbent's weight in gas. In addition to their affinity for different gases, zeolites and some types of activated carbon may utilize their molecular sieve characteristics to exclude some gas molecules from their structure based on the size and shape of the molecules, thereby restricting the ability of the larger molecules to be adsorbed.

Distribution process for oxygen produced by PSA plants
Aside from its use to supply medical oxygen, or as a substitute for bulk cryogenic or compressed-cylinder storage, which is the primary oxygen source for any hospital, PSA has numerous other uses. One of the primary applications of PSA is in the removal of carbon dioxide (CO2) as the final step in the large-scale commercial synthesis of hydrogen (H2) for use in oil refineries and in the production of ammonia (NH3). Refineries often use PSA technology in the removal of hydrogen sulfide (H2S) from hydrogen feed and recycle streams of hydrotreating and hydrocracking units. Another application of PSA is the separation of carbon dioxide from biogas to increase the methane (CH4) ratio. Through PSA the biogas can be upgraded to a quality similar to natural gas. This includes a process in landfill gas utilization to upgrade landfill gas to utility-grade high purity methane gas to be sold as natural gas.

PSA is also used in:


 * Hypoxic air fire prevention systems to produce air with a low oxygen content.
 * On purpose propylene plants via propane dehydrogenation. They consist of a selective medium for the preferred adsorption of methane and ethane over hydrogen.
 * Industrial nitrogen generator units based on the PSA process can produce high-purity nitrogen gas (up to 99.9995%) from compressed air. However, such generators are more suited to supply intermediate ranges of purity and flows. Capacities of such units are given in Nm3/h, normal cubic meters per hour, one Nm3/h being equivalent to 1000 liters per hour under any of several standard conditions of temperature, pressure, and humidity.
 * for nitrogen: from 100 Nm3/h at 99.9% purity, to 9000 Nm3/h at 97% purity;
 * for oxygen: up to 1500 Nm3/h with a purity between 88% and 93%.

In the frame of carbon capture and storage (CCS), research is also currently underway to capture CO2 in large quantities from coal-fired power plants prior to geosequestration, in order to reduce greenhouse gas production from these plants.

PSA has also been discussed as a future alternative to the non-regenerable sorbent technology used in space suit primary life support systems, in order to save weight and to extend the operating time of the suit.

This is the process used in medical oxygen concentrators used by emphysema and COVID-19 patients and others requiring oxygen-enriched air for breathing.

Double Stage PSA
(DS-PSA, sometimes also referred to as Dual Step PSA) With this variant of PSA developed for use in laboratory nitrogen generators, nitrogen gas is produced into two steps: in the first step, the compressed air is forced to pass through a carbon molecular sieve to produce nitrogen at a purity of approximately 98%; in the second step this nitrogen is forced to pass into a second carbon molecular sieve and the nitrogen gas reaches a final purity up to 99.999%. The purge gas from the second step is recycled and partially used as feed gas in the first step.

In addition, the purge process is supported by active evacuation for better performance in the next cycle. The goals of both of these changes is to improve efficiency over a conventional PSA process.

DS-PSA can also be applied to increase the oxygen concentration. In this case, an aluminum silica based zeolite adsorbs nitrogen in the first stage reaching 95% oxygen in the outlet, and in the second stage a carbon-based molecular sieve adsorbs the residual nitrogen in a reverse cycle, concentrating oxygen up to 99%.

Rapid PSA
Rapid pressure swing adsorption, or RPSA, is frequently used in portable oxygen concentrators. It allows a large reduction in the size of the adsorbent bed when high purity is not essential and when the feed gas (air) can be discarded. It works by quickly cycling the pressure while alternately venting opposite ends of the column at the same rate. This means that non-adsorbed gases progress along the column much faster and are vented at the distal end, while adsorbed gases do not get the chance to progress and are vented at the proximal extremity.

Vacuum swing adsorption
Vacuum swing adsorption (VSA) segregates certain gases from a gaseous mixture at near ambient pressure; the process then swings to a vacuum to regenerate the adsorbent material. VSA differs from other PSA techniques because it operates at near-ambient temperatures and pressures. VSA typically draws the gas through the separation process with a vacuum. For oxygen and nitrogen VSA systems, the vacuum is typically generated by a blower. Hybrid vacuum pressure swing adsorption (VPSA) systems also exist. VPSA systems apply pressurized gas to the separation process and also apply a vacuum to the purge gas. VPSA systems, like one of the portable oxygen concentrators, are among the most efficient systems measured on customary industry indices, such as recovery (product gas out/product gas in) and productivity (product gas out/mass of sieve material). Generally, higher recovery leads to a smaller compressor, blower, or other compressed gas or vacuum source and lower power consumption. Higher productivity leads to smaller sieve beds. The consumer will most likely consider indices which have a more directly measurable difference in the overall system, like the amount of product gas divided by the system weight and size, the system initial and maintenance costs, the system power consumption or other operational costs, and reliability.