Talk:Circuit design

Wiki Education Foundation-supported course assignment
This article was the subject of a Wiki Education Foundation-supported course assignment, between 2 February 2021 and 14 May 2021. Further details are available on the course page. Student editor(s): Koeppejk, Schavez63, The Sea Boy 18.

Above undated message substituted from Template:Dashboard.wikiedu.org assignment by PrimeBOT (talk) 19:05, 17 January 2022 (UTC)

Wiki Education Foundation-supported course assignment
This article was the subject of a Wiki Education Foundation-supported course assignment, between 7 January 2020 and 9 May 2020. Further details are available on the course page. Student editor(s): Zampaman92.

Above undated message substituted from Template:Dashboard.wikiedu.org assignment by PrimeBOT (talk) 17:44, 16 January 2022 (UTC)

rewrite
This is not an article about circuit design at all. However, it is a great compilation of "resistor" and "capacitor"! The info seems to be the same as in the articles resistor and capacitor. I think a new article on circuit design might need to be started.--RichG 06:35, 8 November 2005 (UTC)

The content on this page should not even be here. It is a very basic overview of electronic components.

Since article seemed to be a copy-and-paste of Resistor and Capacitor I've replaced it with a basic stub and linked it to the articles it was copying. Astaroth5 11:22, 29 November 2005 (UTC)
 * So I sketched out the beginnings of an article devoted to the topic at hand. DV8 2XL 20:42, 29 November 2005 (UTC)
 * Thanks DV8 2XL, that's an excellent framework to build on! Astaroth5 21:17, 29 November 2005 (UTC)

(Un)Referenced
The treatment in the main article was to provide something for others to build on. It was only done this way as the previous treatment was in the opinion of most off topic. However if it is going to be flagged as unreferenced, I see no other course than to remove all of my edits. I will not be in violation of the no original research policy.


 * I think you might be over-reacting a bit DV8, the unref tag was only making explicit was already obvious from the lack of quoted references, but in any case if I can find the time I'll take another shot at the article in the next few days Astaroth5 22:18, 9 December 2005 (UTC)
 * I have had trouble with this tag in the past, and I have taken a hard line myself on unreferenced work enough that I don't need something that I can have my nose rubbed into hanging around. The tag itself is a weasels tag; call someone out on OR or edit the article - don't just tag and run. DV8 2XL 22:34, 9 December 2005 (UTC)


 * Alright, so it took rather less than a few days! This rewrite gives a few citations, although still not ideal, it should be enough to justify the continued existance of most of the text. Astaroth5 00:03, 10 December 2005 (UTC)

Documentation
The article needs a section on documentation. I have been out of the field for too long to know exactly what is expected these days, and while I suspect not much has changed I don't feel comfortable writing about it lest I leave out something critical. DV8 2XL 16:34, 11 December 2005 (UTC)


 * Done, but it could use a little expansion. Astaroth5 21:58, 12 December 2005 (UTC)

Simply designing the circuit as they go along
Im just wondering if this phrase is useful or not. What does it mean? In a random mannner? In a sequential manner. Im not sure. Is anyone else sure? --Light current 22:43, 3 April 2006 (UTC)

I think it is intended to contrast people designing and building a single system a little at a time ("incrementally") vs. people that design the complete system, then afterwards build it all at once (BigDesignUpFront).

For example, a ham radio operator building a TNC can build it incrementally. He can build a power supply and test it out; an audio amp and test it out; then add a RF recieve amp ... ideally, at each step, he has something useful and functioning. The prototyping techniques allow her to add new wires and transistors, or tear out cheap transistors and cable and replace them with better ones.

On the other hand, people manufacturing an IC must do it all at once. Once an IC is fabbed, it's prohibitively expensive to go back and add or replace any more transistors or wires later.

(PCBs are in-between. The PCB itself is fabbed all-at-once. But it's fairly common for minor fixes to be manually added to the PCB -- a bad trace can be cut; a forgotten connection can be added by soldering on wire.)

--68.0.120.35 14:14, 10 June 2007 (UTC)

External links modified
Hello fellow Wikipedians,

I have just modified 5 external links on Circuit design. Please take a moment to review my edit. If you have any questions, or need the bot to ignore the links, or the page altogether, please visit this simple FaQ for additional information. I made the following changes:
 * Corrected formatting/usage for http://www.seas.upenn.edu/~ee205/Labs97S/Lab4.html
 * Added archive https://web.archive.org/web/20160901160934/http://besttest.com/Courses/DFTBIST.cfm to http://www.besttest.com/Courses/DFTBIST.cfm
 * Corrected formatting/usage for http://www.ita.doc.gov/td/tic/ce_mark/ceFAQ.htm
 * Added archive https://web.archive.org/web/20081024232117/http://export.gov/cemark/doc_ce_mark_main.asp to http://www.export.gov/cemark/doc_ce_mark_main.asp
 * Added archive https://web.archive.org/web/20070409052309/http://ikalogic.com/beg_1_res_v_c.php to http://ikalogic.com/beg_1_res_v_c.php

When you have finished reviewing my changes, you may follow the instructions on the template below to fix any issues with the URLs.

Cheers.— InternetArchiveBot  (Report bug) 02:48, 8 August 2017 (UTC)

Hi
I need help 5.217.74.0 (talk) 10:19, 17 December 2021 (UTC)