Talk:Clipper (electronics)

Necessity for diode in clippers
Can a clipper operate without a diode of some sort? Careful how you answer this one!--Light current 17:42, 31 March 2006 (UTC)

Why would you not want to use a diode? Anyways, how about an operational amplifier, with a gain of 1, given a limited voltage supply. This would, in effect, clip voltages which are at or exceeds the supply voltage. Ronald Ping Man Chan (talk)

merge
The result was not to merge clamper (electronics) into clipper (electronics).

I suggest merging clamper (electronics) into clipper (electronics). Some sources draw a distinction between the two. But I they are so closely related that a single article describing both of them, and the subtle distinction between them, would be better than 2 separate article, each of which re-iterate the subtle distinction between them. --68.0.124.33 (talk) 20:37, 13 September 2008 (UTC)

I disagree. Clipper and clampers, while sounding somewhat similar, with both using diodes, are still quite different, I think. The distinction is not subtle. To understand clampers, an understanding of capacitors and how they charge up to remove the dc component is required. For clippers, there is a more simplistic understanding, where the diode either blocks, or shunts. Also, there are different diodes which could be used, for example, zener diodes as voltage references. Compare this with a clamper, which requires a voltage source - zener diode would not work. Ronald Ping Man Chan (talk) 04:52, 10 March 2009 (UTC)

I disagree too.. Clippers Have no energy storage elements unlike clampers. Should not be merged. —Preceding unsigned comment added by San 013 (talk • contribs) 12:59, 12 June 2009 (UTC)

I also disagree, the two articles are different. This would be like merging passive filter and active filter - one could argue that the ae both the same, yet they are clearly different devices with different functions. Seeing as it has been over a year with the general consensus being not to move, I am archiving this discussion and removing the merge templates -- Jack1993jack (talk) 00:15, 14 January 2010 (UTC)

Image
Image of clipper circuit requested for shunt and series. Ronald Ping Man Chan (talk) 04:55, 10 March 2009 (UTC)
 * Image added of shunt voltage clipper using zener diode(s) Jack1993jack (talk) 19:18, 13 January 2010 (UTC)

The upper circuit won't work as advertised. The zener diode will conduct if the input is more negative than about 0.7 V. For positive voltages it will open only if the voltage exceeds the rating of the zener. So the resulting waveform will be clipped close to GND with a little shift to the negative. However, the image sugests no negative clipping at all. Minor glitches: There should be a blob where the vertical diode wire hits the horizontal wire. The vertical axis of the diagrams should point up, not up and down. The horizontal axis should point left. There are no label axis.-----&lt;(kaimartin)&gt;--- (talk) 14:34, 16 December 2010 (UTC)

I agree - The upper circuit won't work as advertised. The zener diode will conduct if the input is more negative than about 0.7 V. For positive voltages it will open only if the voltage exceeds the rating of the zener. So the resulting waveform will be clipped close to GND with a little shift to the negative. However, the image sugests no negative clipping at all. — Preceding unsigned comment added by 146.64.150.246 (talk) 14:01, 16 August 2012 (UTC)

Copyright problem removed
Prior content in this article duplicated one or more previously published sources. Copied or closely paraphrased material has been rewritten or removed and must not be restored, unless it is duly released under a compatible license. (For more information, please see "using copyrighted works from others" if you are not the copyright holder of this material, or "donating copyrighted materials" if you are.) For legal reasons, we cannot accept copyrighted text or images borrowed from other web sites or published material; such additions will be deleted. Contributors may use copyrighted publications as a source of information, but not as a source of sentences or phrases. Accordingly, the material may be rewritten, but only if it does not infringe on the copyright of the original or plagiarize from that source. Please see our guideline on non-free text for how to properly implement limited quotations of copyrighted text. Wikipedia takes copyright violations very seriously, and persistent violators will be blocked from editing. While we appreciate contributions, we must require all contributors to understand and comply with these policies. Thank you. Osiris (talk) 09:40, 23 June 2012 (UTC)

Square wave analysis
I have removed the claim in the article that square waves are easier to analyse in clipper circuits. I don't see in what way, any analysis I can think of gives either trivial or useless results. The clipping level is the same for any waveform and is determined by the circuit. The phase onset of clipping is certainly easy to calculate for a square wave - it is clipping at all points of the waveform - but that is hardly telling us anything useful. The most complex thing one might want to calculate for a clipper is to determine the harmonic distortion by Fourier analysis. Well a clipped square wave will still be a square wave so the relative harmonic content will not have changed. We thus come to the conclusion by square wave analysis that a clipper introduces no distortion and is, in fact, an attenuator.  Spinning Spark  09:59, 29 January 2014 (UTC)

India Education Program course assignment
This article was the subject of an educational assignment supported by Wikipedia Ambassadors through the India Education Program.

The above message was substituted from by PrimeBOT (talk) on 20:01, 1 February 2023 (UTC)