User:Counsell/sandbox

A heating element converts electricity into heat through the process of resistive or Joule heating. Electric current passing through the element encounters resistance, resulting in heating of the element. Unlike the [Peltier Effect]] this process is independent of the direction of current flow.

Simple metal heating elements




Nichrome
Most heating elements use Nichrome 80/20 (80% nickel, 20% chromium) wire, ribbon, or strip. Nichrome 80/20 is an ideal material, because it has relatively high resistance and forms an adherent layer of chromium oxide when it is heated for the first time. Material beneath this layer will not oxidize, preventing the wire from breaking or burning out.

Resistance wire
may be wire or ribbon, straight or coiled. Used in common items such as toasters and hair dryers, furnaces for industrial heating, floor heating, roof heating, pathway heating to melt snow, dryers, etc. Most common wires are from the following classes


 * Kanthal (FeCrAl) wires
 * Nichrome 80/20 wire and strip
 * Cupronickel (CuNi) alloys for low temperature heating

Etched foil
Etched foil elements are generally made from the same alloys as Resistance wire elements, but are produced with a subtractive photo-etching process that starts with a continuous sheet of metal foil and ends with a complex resistance pattern. These elements are commonly found in precision heating applications such as medical diagnostics and aerospace.

Heat lamps
A high-powered incandescent lamp usually run at less than maximum power to radiate mostly infrared instead of visible light. These are usually found in radiant space heaters and food warmers, taking either a long, tubular form or an R40 reflector-lamp form. The reflector lamp style is often tinted red to minimize the visible light produced; the tubular form is always clear.

Molybdenum disilicide
Molybdenum disilicide (MoSi2, molybdenum silicide), an intermetallic compound, a silicide of molybdenum, is a refractory ceramic with primary use in heating elements. It has moderate density, melting point 2030 °C, and is electrically conductive. At high temperatures it forms a passivation layer of silicon dioxide, protecting it from further oxidation. The application area includes glass industry, ceramic sintering, heat treatment furnaces and semiconductor diffusion furnaces.

PTC Ceramic elements
PTC ceramic: this material is named for its positive thermal coefficient of resistance (i.e., resistance increases upon heating). Most ceramics have a negative coefficient, whereas most metals have positive values. While metals do become slightly more resistant at higher temperatures, this class of ceramics (often barium titanate and lead titanate composites) has a highly nonlinear thermal response, so that it becomes extremely resistant above a composition-dependent threshold temperature. This behavior causes the material to act as its own thermostat, since current passes when it is cool, and does not when it is hot. Thin films of this material are used in automotive rear-window defrost heaters, and honeycomb-shaped elements are used in more expensive hair dryers and space heaters.

Tubular heating elements
Tubular (sheathed) elements normally comprise a fine coil of resistance heating alloy wire, usually Nichrome (NiCr) that is connected at each end to a terminal pin and is electrically insulated from a metallic concentric tube by in a ceramic insulating material, fused MgO powder. The tube ends are frequently equipped with beads of insulating material such as ceramic or silicone rubber, or a combination of both to prevent the penetration of moisture in to the element. These can be a straight rod (as in toaster ovens) or bent to a shape to span an area to be heated (such as in electric stoves, ovens, and coffee makers).

Screen-printed elements
Screen-printed metal–ceramic tracks deposited on ceramic insulated metal (generally steel) plates have found widespread application as elements in kettles and other domestic appliances since the mid-1990s.

Thick film technology
Heating elements for high-temperature furnaces are often made of exotic materials, including platinum, molybdenum disilicide, molybdenum (vacuum furnaces) and silicon carbide. Silicon carbide igniters are common in gas ovens.

Electric stoves
normally have three types of heating elements, surface burners, bake elements and broil elements. The Surface Burner Elements are typically either a coil type, solid type or a ribbon coil as used in smooth top ranges. All of these consist of heating wire that uses an electric current to produce heat. The Broil Element is the heating element that is found at the top of the oven and produces a very high heat for broiling. This element is not used for the majority of baking and only provides about 10% of the heat. The Bake Element is found at the bottom of the oven. Most ovens use both the bake element and the broil element in a bake cycle, but with the bake element performing 90% of the heating.