User talk:Shmily2012

Welcome to Wikipedia. Everyone is welcome to contribute constructively to the encyclopedia. However, please do not add promotional material to articles or other Wikipedia pages. Advertising and using Wikipedia as a "soapbox" are against Wikipedia policy and not permitted. Take a look at the welcome page to learn more about Wikipedia. Thank you. Mean as custard (talk) 07:43, 15 May 2012 (UTC)

Flotation machine can meet the performance requirements of the flotation process
Flotation Machine can be used to separate nonferrous metal, ferrous metal, heavy metal, nonmetallic mine, chemical material and recycling minerals. Each chute can inhale gas, sink magma, separate. No assiting equipments are required, and Flotation Machine must be levelly installed. Flotation Machine is easy to change the flow chart. The cycling way of magma is very reasonable. Flotation Machine can reduce the impurities to a great extent. There is automatic equipment on the magma surface, easy to adjust. The impeller also owns the upper and lower retroversion blade. The upper one makes the magma cycle upward, while the lower one makes the magma cycle downward.

Flotation machine has many same characteristics with other machines, such as reliable working, wear-resisting, low power consumption, simple structure and low price. It also should have the special requirements like followings to meet the flotation requirements:

1. Well inflatable role: Flotation machine must guarantee a certain of air amount be absorbed or pressed into the ore pulp and disperses in all the slot. For the air can be dispersed more finer and more uniform, the contact between the ore grains and air bubbles will be more so that the flotation efficiency can be higher.

2. Mixing role: Flotation machine should have well mixing role to make the ore grains suspension and distributed in all the slot uniformly. At the same time, the machine can promote the solvation of some hard dissolved agentias, which is in favor of the full function between the agentias and ore grains.

3. Circular flow function: In flotation machine, the circular flow of ore pulp can make more contact between the ore grains and air bubbles. Get ball mill,beneficiation,Mineral Processing From http://www.ballmill8.com

Medium Speed wet milling machine and the relationship between the Ball Mill
So far, the world's medium-speed milling machines are dry law. Hot air carrier that is, separation, sorting products. Therefore in need of a massive and complicated: medium heat generator, fans, vents Central, separator, explosion-proof system (inert gas source), dedusting system, sealing measures and it is difficult to adapt to the high moisture materials, a fine-grained access-class products in the high temperature operating equipment damage and fast, and the situation difficult to control; complete machine too tall. principle but because of movement determined by the grinding efficiency, and in electricity, the cement industry in the milling system is widely used, but no First, wet operations. Therefore, the principle of movement determined by the grinding efficiency has not been fully exploited.

2 and the Mill Although conventional campaign decided by the principle of grinding mill less than the speed, but the wet process is significantly higher than that of dry. Normally, the same conditions wet process Bian Process 30% energy saving. Because wet (water) by grinding effect, and water is the simplest, cheapest, "aids." Its will to a large extent influence the fragmentation of materials. Adsorbing water because of the solid surface (the activity of a molecule), the surface free energy and the elastic deformation can be reduced, resulting in the weakening bond together to promote and accelerate the materials crack formation and expansion, the reduction of the strength of the materials -- -- This is the famous "out Binchaer effect." The result: Wet operations for the period to achieve fineness, it can improve product yield, or yield to achieve period, the fracture particles can promote products mill will be more detailed.

3 envisaged, if the mill rate to avoid the disadvantages, while retaining the principle of movement in the rate decisions of the mill grinding efficiency at the same time allow a Wet Ball Mill with water transmission and other election materials and the simplicity of the wet efficient. designed to speed in the wet mill. its effect should be complementary. be wet grinding technology to meet a variety of needs: FGD desulfurization agents such as power plants, coal slurry preparation; while achieving energy conservation, efficiency, energy, environmental protection simple, reliable, the purpose of applicability stronger. This is the speed in the wet grinding birth of the technical background. Get rotary kiln,ball mill,Mineral Processing From http://www.ballmill8.com

Principle processes of flotation separation of Polymetallic ores
Direct Preferential Flotation Definition of this method is: separate various helpful minerals in proper order. With its feature of high flexibility, it can adapt the change of ore grade, especially for sulphide ore of high grade. Xilin, Fankou, Lechang lead-zinc dressing plant of our country, and Laisvall lead-zinc dressing plant of Sweden all adopt this method.

Combined Flotation Flowsheet Firstly, get mixed concentrate through the emersion of all useful minerals in ores; secondly, separate various helpful minerals in sequence from mixed concentrate. These two steps together are called part of amalgamate flotation Flowsheet. This process is suitable for treat raw ores of complex structure, fine embedded grains, and low content of sulfide mineral, which are in close symbiosis relationship. Because this process can simplify process, reduce ores’ over grinding, so as to benefit separation. Almarc Lead-zinc plant of former Soviet Union adopts preferential flotation this process. By using this process, we can get higher index than preferential flotation improve 10% of lead concentrate ore grade and 4.5% of zinc concentrate ore grade, raise the rate of multipurpose utilization from 75.4% to 83.7%, and double labor productivity. Qingchengzi zinc-lead ore dressing plant and Xiaotieshan copper ore dressing plant of our country adopt this process.

Part of Amalgamate Flotation Flowsheet We can get mixed concentrate by the emersion of two useful minerals in ores together, then separate single concentrate from the mixed concentrate. The two stages together are called part of amalgamate flotation Flowsheet, which is the most widely used process in production. It is quite economical to adopt this process when raw ores contain low-grade nitrogen, copper-lead, copper-zinc, and lead-zinc.

Iso-flotability Flotation Process According to minerals’ flotability in ores, mineral assemblages of good, medium and worse flotability are separated through flotation separation. Secondly, different helpful minerals are selected out from all mixed concentrates, which is called iso-flotability flotation process. For example, Huangshapinng lead-zinc ore dressing plant of our country, and Zheskaz of former Soviet Union both adopt this process. Get ball mill,ball mill,beneficiation From http://www.ballmill8.com

The basic principle of ore grinding process
When the ore grinding machine are rotating in a certain rotate speed, the ore grinding medium in barrel will produce centrifugal force by rotating so that there will be certain friction between ore grinding medium and barrel. The friction will drive the ore grinding medium rotating with the barrel and reach a certain level. When its own gravity (centripetal force of gravity) are larger than centrifugal force, the ore grinding medium will leave the barrel then fall in projectile way. When the medium are falling down, impact force are produced and the grinding medium can crush the ores. At the same time, in the mill operation process, there are sliding phenomenon and extrusion phenomenon that is produced by lining medium to outer medium in the ore grinding medium, which can produce abrasive and extrusion action to ores. So the ores can be ground by combined effect of impact force, grinding force and extrusion pressure of ore grinding medium.

The ore grinding function of ore grinding machine are like the following picture:

Lifting height and motion trail of projectile action of ore grinding medium depend on rotating speed of grinding machine and the filled amount of ore grinding medium. Both the low speed and high speed will have direct influence on the performance of grinding machine. The grinding medium moving condition in three kinds of different working speed are:

1. Grinding machine running in a low speed(pic.a) The rotating speed is not high so the lifting height of grinding medium is low and the grinding medium will fall to the bottom of barrel along to their own inclined plane for circulating. The medium is in spilling state and has smaller impact. The abrasive and extrusion action are formed by rolling action among mediums. Ball has less grinding action to materials.

2．Grinding machine running in a normal speed(pic.b) The rotating speed is higher so the lifting height of grinding medium is high and the grinding medium will be up to a certain height with barrel circular motion, then leave the barrel in a certain velocity and do fall down movement along parabolic path. At this time, the grinding medium has high impact and the abrasive and extrusion action will get sufficient exertion. The materials are ground in the most intense level. Most of grinding machines are working in such a ore grinding condition.

3. Centrifugal operation(pic.c) When the rotating speed of ore grinding machine is enhanced to a limit numerical value, all the grinding medium will do concentric rotation with the barrel and will not fall down, which will be called centrifugal operation. When the medium produces centrifugal operation, the ore grinding action will be lost in theory. So the grinding machine should work in the rotation speed which is below centrifugal operation. Get Mineral Processing,rotary kiln,beneficiation From http://www.ballmill8.com

The difference between Ball Mill and Raymond Mill
Ball Mill materials is being broken, further crush the key equipment. Mill widely used in cement, Portland products, new building materials, refractories, fertilizers, as well as black and non-ferrous metal processing industries such as the production of glass ceramics, various ores and other materials may be grinding of dry or wet grinding.

Mill principle: The ball mill for the installation of horizontal rotating cylinder, outer edge of which lies Gear, two warehouses, lattice-type ball mill. Feed materials from the device into the compound empty-axis spiral uniform access to the first Mill Wharf, the warehouses have stepped liner or corrugated liner, the contents of different specifications Ball, the centrifugal force will have a rotating cylinder ball to a certain altitude sets, and have severe impact on materials and grinding role. Materials in the first positions to grinding, single-layer at the plate in the second warehouse stores, the warehouses incalculable-liner with a ball, will further polishing materials. Discharge through the grate of powder from plate to complete grinding operations.

Mill structural characteristics: Feeding this machine by the Department of the Ministry of material, Rotary Department, the Department of transmission (reducer, small transmission gears, motors, electronic control), and other key components. Casting a hollow shaft, lined Looking to the future, casting a rotary gear hobbing processing, cylinder liner wear in incalculable, has good wear resistance. The smooth functioning of the machine, is reliable.

R-type milling machine from the host unit structure, analysis of pipeline installation, blower, according to user needs can be fitted with a broken machine, hoist, electromagnetic Vibrating Feeder, electric motor control components. Materials are needed to crush size, the materials hoist will be sent to storage hopper, to be expected by the vibrating feeder uniform for the mainframe into Raymond Mill grinding room, as when centrifugal rotary role Roll out swinging, press the grinding part of the shovel blade materials to roll grinding and grinding Central, as Roll rolling to achieve the aim of crushing. After grinding the powder material with the circulating air blower into the analysis was conducted at the election, fine through coarse material to re-grinding, qualified powder into the air, finished with the whirlwind set of powder, the powder discharge pipe, which is refined. In Raymond Mill grinding mill indoors due to certain materials in the water, grinding, heat, air-water evaporation, and the pipeline unit interface is not well outside gas inhalation, the cycle of increased pressure to ensure that the mill under negative pressure, the increase in gas flow through the tube into the wind I precipitator was after purification into the atmosphere.

Raymond Mill unit structure features: One, three-dimensional structure, small footprint, turnkey highly refined powder expected from the block of independent self-production system.

2, refined powder fineness of uniform rate of 99% on screen, it is difficult to other milling equipment available.

3, the Drive installations in confined pulley and gear box, transmission smooth, reliable operation.

4, the important components are used quality steel, wear-resistant performance of wear resistant materials are used, the whole high wear resistance, reliable operation. 5, the electrical system is centralized control, milling plant can be realized no one basic operations and maintenance.

Raymond Mill unit structure features: 1, milling machines used in the process, there should be a fixed custody staff, operators must have a certain level of technology. Mill installed before the operator must conduct the necessary technical training so that they understand the principle of milling machine, familiar with the rules.

2, for the mill to normal, should develop equipment "safe operation of equipment maintenance system" can guarantee long-term security mill operation, a necessary repair tools and grease and corresponding accessories.

3, mill use for a period of time, it should repair, while Roller Mill Central blade repair and replacement of vulnerability, Roller device in use before and after the bolt nut should be carefully examined to see if it is loose, Lubricants and whether adequate.

4, Raymond Mill Roll devices around for more than 500 hours to replace Roll, roll on the roller bearing to the inner cleansing, and replace damaged parts, tools can be manually refueling pumps guns and butter. Get ball mill,ball mill,beneficiation From http://www.ballmill8.com