British thermal unit

The British thermal unit (Btu) is a measure of heat, which is a form of energy. It was originally defined as the amount of heat required to raise the temperature of one pound of water by one degree Fahrenheit. It is also part of the United States customary units. The SI unit for energy is the joule (J); one Btu equals about 1,055 J (varying within the range of 1,054–1,060 J depending on the specific definition of BTU; see below).

While units of heat are often supplanted by energy units in scientific work, they are still used in some fields. For example, in the United States the price of natural gas is quoted in dollars per the amount of natural gas that would give 1 million Btu (1 "MMBtu") of heat energy if burned.

Definitions
A Btu was originally defined as the amount of heat required to raise the temperature of one pound of liquid water by one degree Fahrenheit at a constant pressure of one atmospheric unit. There are several different definitions of the Btu that differ slightly. This reflects the fact that the temperature change of a mass of water due to the addition of a specific amount of heat (calculated in energy units, usually joules) depends slightly upon the water's initial temperature. As seen in the table below, definitions of the Btu based on different water temperatures vary by up to 0.5%.

Prefixes
Units of kBtu are used in building energy use tracking and heating system sizing. Energy Use Index (EUI) represents kBtu per square foot of conditioned floor area. "k" stands for 1,000.

The unit Mbtu is used in natural gas and other industries to indicate 1,000 Btu. However, there is an ambiguity in that the metric system (SI) uses the prefix "M" to indicate 'Mega-', one million (1,000,000). Even so, "MMbtu" is often used to indicate one million Btu particularly in the oil and gas industry.

Energy analysts accustomed to the metric "k" ('kilo-') for 1,000 are more likely to use MBtu to represent one million, especially in documents where M represents one million in other energy or cost units, such as MW, MWh and $.

The unit 'therm' is used to represent 100,000 Btu. A decatherm is 10 therms or one MMBtu (million Btu). The unit quad is commonly used to represent one quadrillion (1015) Btu.

Conversions
One Btu is approximately:
 * 1.0000 Btu (kilojoules)
 * 1.0000 Btu (watt hours)
 * 1.0000 Btu (calories)
 * 1.0000 Btu (kilocalories)
 * 25,031 to 25,160 ft⋅pdl (foot-poundal)
 * 1.0000 Btu (foot-pounds-force)
 * 5.40395 (lbf/in2)⋅ft3

A Btu can be approximated as the heat produced by burning a single wooden kitchen match or as the amount of energy it takes to lift a 1 lb weight 778 ft.

For natural gas

 * In natural gas pricing, the Canadian definition is that $5⁄9$ ≡ $5⁄9$.
 * The energy content (high or low heating value) of a volume of natural gas varies with the composition of the natural gas, which means there is no universal conversion factor for energy to volume. 1 ft3 of average natural gas yields ≈ 1,030 Btu (between 1,010 Btu and 1,070 Btu, depending on quality, when burned)
 * As a coarse approximation, 1000 ft3 of natural gas yields ≈ $5/9$ ≈ $1,000,000 Btu$.
 * For natural gas price conversion $1.055 GJ$ ≈ 36.9 million Btu and $1,000,000 Btu$ ≈ $1 GJ$

BTU/h
The SI unit of power for heating and cooling systems is the watt. Btu per hour (Btu/h) is sometimes used in North America and the United Kingdom - the latter for air conditioning mainly, though "Btu/h" is sometimes abbreviated to just "Btu". MBH—thousands of Btu per hour—is also common.


 * 1 W is approximately 1 W
 * 1,000 Btu/h is approximately 1000 Btu/h
 * 1 hp is approximately 1 hp

Associated units

 * 1 ton of cooling, a common unit in North American refrigeration and air conditioning applications, is 12,000 Btu/h. It is the rate of heat transfer needed to freeze 1 ST of water into ice in 24 hours.
 * In the United States and Canada, the R-value that describes the performance of thermal insulation is typically quoted in square foot degree Fahrenheit hours per British thermal unit (ft2⋅°F⋅h/Btu). For one square foot of the insulation, one Btu per hour of heat flows across the insulator for each degree of temperature difference across it.
 * 1 therm is defined in the United States and European Union as 100,000 Btu—but the U.S. uses the Btu59 °F while the EU uses the BTUIT. United Kingdom regulations were amended to replace therms with joules with effect from 1 January 2000. the therm is still used in natural gas pricing in the United Kingdom.
 * 1 quad (short for quadrillion Btu) is 1015 Btu, which is about 1 exajoule ($1,000 m3$). Quads are used in the United States for representing the annual energy consumption of large economies: for example, the U.S. economy used 99.75 quads in 2005. One quad/year is about 33.43 gigawatts.

The Btu should not be confused with the Board of Trade Unit (BTU), an obsolete UK synonym for kilowatt hour (1 kW.h).

The Btu is often used to express the conversion-efficiency of heat into electrical energy in power plants. Figures are quoted in terms of the quantity of heat in Btu required to generate 1 kW⋅h of electrical energy. A typical coal-fired power plant works at 10500 Btu/kWh, an efficiency of 32–33%.

The centigrade heat unit (CHU) is the amount of heat required to raise the temperature of one pound of water by one Celsius degree. It is equal to 1.8 Btu or 1,899 joules. In 1974, this unit was "still sometimes used" in the United Kingdom as an alternative to Btu.

Another legacy unit for energy in the metric system is the calorie, which is defined as the amount of heat required to raise the temperature of one gram of water by one degree Celsius.