Toyota A engine

The Toyota A Series engines are a family of inline-four internal combustion engines with displacement from 1.3 L to 1.8 L produced by Toyota Motor Corporation. The series has cast iron engine blocks and aluminum cylinder heads. To make the engine as short as possible, the cylinders are siamesed.

The development of the series began in the late 1970s, when Toyota wanted to develop a completely new engine for the Toyota Tercel, the successor of Toyota's K engine. The goal was to achieve good fuel efficiency and performance as well as low emissions with a modern design. The A-series includes one of the first Japanese mass-production DOHC, four-valve-per-cylinder engines, the 4A-GE, and a later version of the same engine was one of the first production five-valve-per-cylinder engines.

Toyota joint venture partner Tianjin FAW Xiali produces the 1.3 L 8A and resumed production of the 5A in 2007.

1A
The 1.5 L 1A was produced between 1978 and 1980. All variants were belt-driven 8-valve counter-flow SOHC engines with a single, twin-barrel downdraft carburetor. It used Toyota's Turbulence Generating Pot (TGP) lean combustion system to meet Japanese emissions standards at the time with only an oxidation (2-way) catalyst. The 1A engine was only 21.6 in long.

1A-C
Applications:
 * AL10 Tercel

1A-U
Using Toyota two-way catalyst.

Output:
 * 80 PS at 5,600 rpm and 11.5 kgm at 3,600 rpm (compression at 9.0:1)

Applications:
 * AL10 Tercel/Corsa (Japan only)

2A
The 1.3 L 2A was produced from 1979 through 1989. 2A engines in 1982 onwards AL20 Tercels have a slightly different valve cover and timing belt cover than early AL11 Tercels, as well as an automatic choke, and automatically controlled hot air intake (HAI) system. It also has higher compression ratio, and reformulated combustion chambers to improve the fuel economy and emissions. All variants used belt-driven SOHC eight-valve counter-flow cylinder heads with a single downdraft carburetor.

2A, 2A-L, 2A-LC
Output:
 * 65 PS at 6,000 rpm and 98 Nm at 3,800 rpm (compression at 9.3:1)

Applications:
 * AE80 Corolla 1983–1985 (excluding Japan, 2A-LC in Australia)
 * AL11 Tercel 1979–1982 (excluding Japan and North America)
 * AL20 Tercel 1982–1984 (excluding Japan and North America)

2A-U, 2A-LU
Using Toyota TTC-C catalytic converter.

Output:
 * 75 PS at 6,000 rpm and 106 Nm at 3,600 rpm (compression at 9.3:1)

Applications:
 * AE80 Corolla 1983–1985 (Japan only)
 * AL20 Corolla II 1982–1986 (Japan only)
 * AL11 Corsa (Japan only)
 * AL20 Corsa 1982–1989 (Japan only)
 * AE80 Sprinter 1983–1985 (Japan only)
 * AL11 Tercel
 * AL20 Tercel 1982–1989 (Japan only)

3A
The 1.5 L 3A was produced from 1979 through 1989. The 3A engine is the successor of Toyota's first A engine, the 1A. All variants were belt-driven eight-valve counter-flow SOHC engines but no longer used Toyota's "Turbulence Generating Pot" pre-combustion system from the 1A.

3A, 3A-C
Output:
 * 71 PS at 5,600 rpm and 108 Nm at 3,800 rpm (compression at 9.0:1, European spec)
 * 60 hp at 4,500 rpm (N. America, AL-21 3 door liftback)
 * 62 hp at 4,800 rpm (N. America, AL-25 5-door wagon)

Applications:
 * AL12 Tercel 1979–1982 (excluding Japan)
 * AL21/25 Tercel 1982–1988 (excluding Japan)

3A-U, 3A-LU
Using Toyota TTC-C catalytic converter. On some models marked as 3A-II.

Output:
 * 83.5 PS at 5,600 rpm and 118 Nm at 3,600 rpm (compression at 9.0:1)

Applications:
 * AA60 Carina 1981–1987 (Japan only)
 * AT150 Carina 1984–1988 (Japan only)
 * AE70 Corolla 1979–1983 (Japan only)
 * AE81/85 Corolla 1983–1987 (Japan only)
 * AL21 Corolla II 1982–1986 (Japan only)
 * AT140 Corona 1982–1987 (Japan only)
 * AT150 Corona 1983–1987 (Japan only)
 * AL12 Corsa (Japan only)
 * AL21/25 Corsa 1982–1989 (Japan only)
 * AW10 MR2 1984–1989 (Japan only)
 * AE70 Sprinter 1979–1983 (Japan only)
 * AE81/85 Sprinter 1983–1987 (Japan only)
 * AL25 Sprinter Carib 1982–1988 (Japan only)
 * AL21/25 Tercel 1982–1989 (Japan only)

3A-HU
High compression version with Toyota TTC-C catalytic converter.

Output:
 * 86 PS at 6,000 rpm and 121 Nm at 4,000 rpm (compression at 9.3:1)

Applications:
 * AL21 Corolla II 1982–1984 (Japan only)
 * AL21 Corsa 1982–1984 (Japan only)
 * AL21 Tercel 1982–1984 (Japan only)

3A-SU
Twin carburetted swirl-intake version with Toyota TTC-C catalytic converter, introduced in August 1984 along with a facelift for the Tercel (and its sister variants) in Japan. Features two variable-venturi carburetors, which Toyota wanted to test in Japan before launching them in export along E series engine, albeit in single carburetted version. Because of the swirl-intake, the sealing surface between cylinder head and valve cover is different from other SOHC A-engines, featuring vertical curves on the manifold side of the head. Thus, those parts are not interchangeable between each other. The swirl was supposed to improve burning of the air-fuel mixture, thus enabling cleaner emissions, improving fuel economy, and increasing power.

Output:
 * 90 PS at 6,000 rpm (compression at 9.3:1)

Applications:
 * AL21 Corolla II 1984–1986 (Japan only)
 * AL21/25 Corsa 1984–1989 (Japan only)
 * AL25 Sprinter Carib 1984–1988 (Japan only)
 * AL21/25 Tercel 1984–1989 (Japan only)

4A
The 4A was produced from 1980 through 2002. All 4A engines have a displacement of 1587 cc. The cylinder bore was enlarged from the previous 3A engines at 81 mm, but the stroke remained the same as the 3A at 77 mm, giving it an over-square bore/stroke ratio which favours high engine speeds.

Numerous variations of the 4A design were produced, from basic SOHC 8-valve all the way to DOHC 20-valve versions. The power output also varied greatly between versions, from 70 hp at 4,800 rpm in the basic California-spec 4A-C to 170 PS at 6,400 rpm in the supercharged 4A-GZE.

4A, 4A-C, 4A-L, 4A-LC
The basic 4A is a SOHC 8 valve carburated engine which produces 78 - 90 PS at 4800 rpm and 115 Nm of torque at 2800 rpm, though the power and torque output figures vary between different regions of the world. in European versions, the combustion chambers were reformulated in early 1986, resulting in an increase of 2 hp, up to 86 PS at 5600 rpm, along with improvements in fuel economy and emissions.

North American market engines:
 * 4A-LC 1.6 L I4, 8-valve SOHC, 70 hp at 4800 rpm


 * 4A-C 1.6 L I4, 8-valve SOHC, 74 hp at 5200 rpm

European (and other) market engines: (excepting Sweden and Switzerland)
 * 4A-L 1.6 L, I4, 8-valve SOHC, 79 PS at 5600 rpm, and torque 12.5 kgm at 4000 rpm (compression at 9.0:1) (Indonesia)
 * 4A-L 1.6 L, I4, 8-valve SOHC, 84 PS at 5600 rpm, and torque 13.3 kgm at 3600 rpm (compression at 9.3:1) (Europe)

Australian/Swiss/Swedish market engines: Australia, Sweden, and Switzerland shared emissions rules for a period in the 1970s and eighties.
 * 4A-LC 1.6 L, I4, 8-valve SOHC, 78 PS at 5600 rpm


 * Applications:
 * AT151 Carina II 1983–1987 (Europe only)
 * AT160 Celica 1985–1989 (excluding Japan)
 * AE71 Corolla 1982–1984 (North America, Australia & South Africa only)
 * AE82/86 Corolla 1983–1987 (excluding Japan)
 * AT151 Corona 1983–1987 (excluding Japan)
 * A60 Daihatsu Charmant 1984-1987 (excluding Japan)
 * Elfin Type 3 Clubman
 * Chevrolet Nova (USA NUMMI rebadged Sprinter) 1985-1988

4A-ELU
Fuel injection was added. This increased output to 100 PS at 5600 rpm and 13 kgm at 4000 rpm. This version is also equipped with Toyota TTC-C catalytic converter.

Applications:
 * AT151 Carina 1984–1988 (Japan only)
 * AE82 Corolla 1983–1987 (Japan only)
 * AE82 Sprinter 1983–1987 (Japan only)

4A-F
A narrow-valve (22.3°) DOHC 16-valve carburetor-equipped version, the 4A-F, was produced from 1987 through 1990. Output was 95 PS at 6,000 rpm and 13.0 kgm at 3,600 rpm (compression at 9.5:1, EU spec). This engine featured an aluminum-alloy cylinder head with scissor-gear driven twin overhead camshafts, centered spark plugs, and pent-roof combustion chambers which were designed to improve thermal efficiency. It also featured a fully counterweighted crankshaft with five journals and eight balance weights. It even employed a "slave cam system", in which the camshafts are geared together and driven off one camshaft's sprocket. The 4A-F was designed to provide more powerful torque in the low-to-mid RPM range, as well improve top-end power output.



Applications:
 * AT171 Carina II 1987–1992 (Europe only)
 * AE92/95 Corolla 1987–1992 (excluding Japan)
 * AE95 Corolla 1988–1989 (Japan only)
 * AE101 Corolla 1992–1998 (Asia, Africa & Latin-America)
 * AE111 Corolla 1997–2001 (Asia, Africa & Latin-America)
 * AT171/177 Corona 1987–1992 (excluding Japan)
 * AE95 Sprinter 1988–1989 (Japan only)

4A-FE


The fuel injected 4A-FE is the successor of the carbureted 4A-F, manufactured from 1987–2001. Toyota designed this engine with fuel economy in mind. The 4A-FE is basically the same as the 4A-F (introduced in the sixth generation of Corollas), the most apparent difference being the electronic fuel injection system as noted by the 'E'. The engine was succeeded by the 3ZZ-FE, a 1.6-liter engine with VVT-i technology.

There are three generations of this engine, which can be identified by the external shape of the engine. The first generation (1987–1996) featured a plate on the head which read "16 valve EFI" and fuel injectors in the head.

The second generation had a higher profile cam design in the head, a cam cover with ribs throughout its length, and fuel injectors in the intake manifold runners. Mechanically, the late-model engines received MAP load sensing and redesigned pistons, intake ports, and intake manifold. The second generation engine was produced from 1992–1998 (1993–1996 in the US).

The third generation (1996–2001) was released exclusively for the Asian market (Japan, Philippines, Pakistan, Thailand, Indonesia, and Malaysia) only. Although it is very similar to the second generation externally, it only has a slight difference in the top section of the intake manifold and throttle body. This last generation also has a higher additional output of 5 hp compared to the second generation.


 * Engine displacement: 1587 cc
 * Layout: DOHC Inline-4
 * Valves: 16, 4 for each cylinder
 * Redline: 6300 rpm
 * Compression ratio: 9.5:1
 * Fuel Delivery System: TCCS or MPFI

North American market engines:
 * 102 hp at 5,800 rpm, and torque 14.8 kgm at 4,800 rpm

European market engines:
 * 105 PS at 6,000 rpm, and torque 14.5 kgm at 3,200 rpm

Asian market engines:
 * 115 PS at 6,000 rpm

Note: power and torque specs for North America and Europe are from the 1988–1992 Corollas.

The 4A-FE is different from the 4A-GE in terms of performance and power. Although both have the same displacement and are DOHC, they were optimized for different uses. The first obvious difference are the valves, the engine's intake and exhaust valves were placed 22.3° apart (compared to 50° in the G-Engines). The second is that it employed a "slave cam system", the camshafts being geared together and driven off one camshaft's sprocket (both camshafts' sprockets on the G-Engine are rotated by the timing belt). Some of the less directly visible differences were poorly shaped ports in the earlier versions, a slow burning combustion chamber with heavily shrouded valves, less aggressive camshaft profiles, a cast crankshaft (rather than a forged crankshaft in the 4A-GE), ports of a small cross sectional area, a very restrictive intake manifold with long runners joined to a small displacement plenum and other changes. Even though the valve angle is closer to what is considered in some racing circles to be ideal for power (approximately 25 degrees), its other design differences and the intake which is tuned for a primary harmonic resonance at low RPM means that it has about 10% less power compared to the 4A-GE engine. This engine design improves fuel efficiency and torque, but compromises power. Power ratings varied from 100 – in the US market.


 * Applications:


 * AT220 Avensis 1997–2000 (excluding Japan)
 * AT171/175 Carina 1988–1992 (Japan only)
 * AT190 Carina 1984–1996 (Japan only)
 * AT171 Carina II 1987–1992 (Europe only)
 * AT190 Carina E 1992–1997 (Europe only)
 * AT180 Celica 1989–1993 (excluding Japan)
 * AE92/95 Corolla 1988–1997
 * AE101/104/109 Corolla 1991–2002
 * AE111/114 Corolla 1995–2002
 * AE101 Corolla Ceres 1992–1998 (Japan only)
 * AE111 Corolla Spacio 1997–2001 (Japan only)
 * AT175 Corona 1988–1992 (Japan only)
 * AT190 Corona 1992–1996
 * AT210 Corona 1996–2001
 * AE95 Sprinter 1989–1991 (Japan only)
 * AE101/104/109 Sprinter 1992–2002 (Japan only)
 * AE111/114 Sprinter 1995–1998 (Japan only)
 * AE95 Sprinter Carib 1988–1990 (Japan only)
 * AE111/114 Sprinter Carib 1996–2001 (Japan only)
 * AE101 Sprinter Marino 1992–1998 (Japan only)
 * AE92/AE111 Corolla/Conquest 1993–2002 (South Africa)
 * Geo Prizm base model (based on Toyota AE92/AE101 chassis) 1989–1997

4A-FHE
Same as the first generation 4A-FE, only more aggressive tune for more output. Called an EFI-S engine.

Output:
 * 110 PS at 6,000 rpm and 14.5 kgm at 4,800 rpm (compression at 9.5:1)

Applications:
 * AT171 Carina 1990–1992 (Japan only)
 * AE95 Sprinter Carib 1990–1995 (Japan only)

4A-GE (16-valve)


The 4A-GE was a series of high-performance four-cylinder twincam engines made by Toyota in collaboration with Yamaha Motor Corporation. The cylinder head was developed by Yamaha and was built at Toyota's Shimoyama plant alongside the 4A and 2A engines. The reliability and performance of these engines has earned them a fair number of enthusiasts and a fan base as they are a popular choice for an engine swap into other Toyota cars such as the KE70 and KP61. New performance parts are still available for sale even today because of its strong fan base. Production of the various models of this version lasted for five generations, from May 1983 through 1991 for 16-valve versions and the 20-valve 4A-GE lasting through 2000.

First Generation "Blue Top" (Early Bigport)
The first-generation 4A-GE which was introduced in May 1983 replaced the 2T-G as Toyota's most popular twincam engine. This engine was identifiable via silver cam covers with the lettering on the upper cover painted black and blue, as well as the presence of three reinforcement ribs on the back side of the block. It was extremely light and strong for a production engine using an all-iron block, weighing in at only 123 kg - over fifteen percent reduction compared to 2T-GEU. It was also 4 dB quieter. While originally conceived of as a two-valve design, Toyota and Yamaha changed the 4A-GE to a four-valve after a year of evaluation.

The 4A-GE produced 112 hp at 6,600 rpm and 13.4 kgm of torque at 4,800 rpm in the American market. The use of a vane-type air flow meter (AFM), which restricted air flow slightly but produced cleaner emissions that conformed to the U.S. regulations, limited the power considerably - the Japanese model, which uses a manifold absolute pressure (MAP) sensor, was originally rated at 130 PS. However, this was a gross power rating and the engine was later re-rated at 120 PS in net output. Nonetheless, Japanese cars tested no faster than their American counterparts despite their higher power rating and a lower curb weight.

Yamaha designed the engine for performance; the valve angle was a relatively wide 50 degrees, which at the time was believed to be ideal for high power production. Today, more modern high-revving engines have decreased the valve angle to 20 to 25 degrees, which allows for a smaller and more compact cylinder head. This is now believed to be ideal for high-revving engines with high specific power outputs, however most high-performance racing engines still employ wide valve angles which allow for straighter ports and more efficient air flow.

The first-generation 4A-GE is nicknamed the "bigport" engine because it had intake ports of a very large cross-sectional area. While the port cross-section was suitable for a very highly modified engine at very high engine speeds, it caused a considerable drop in low-end torque due to the decreased air speeds at those rpm. To compensate for the reduced air speed, the first-generation engines included the T-VIS feature, in which dual intake runners are fitted with butterfly valves that opened at approximately 4,200 rpm. The effect is that at lower rpm (when the airspeed would normally be slow) four of the eight runners are closed, which forces the engine to draw in all its air through half the runners in the manifold. This not only raises the airspeed which causes better cylinder filling, but due to the asymmetrical airflow a swirl is created in the combustion chamber, meaning better fuel atomization. This enabled the torque curve to still be intact at lower engine speeds, allowing for better performance across the entire speed band and a broad, flat torque curve around the crossover point. During rising engine speed, a slight lurch can occur at the crossover point and an experienced driver will be able to detect the shift in performance. Production of the first-generation engine model lasted until May 1987.

Second Generation "Red & Black Top" (Late Bigport)
The second-generation 4A-GE produced from June 1987 to May 1989 featured larger diameter bearings for the connecting-rod big ends 42 mm and added four additional reinforcement ribs on the back of the engine block, for a total of seven. The T-VIS feature is retained, as well as the MAP sensor (MAF sensor in the US-market). It is visually similar to the first-generation engine (only the upper cam cover now featured red and black lettering) and the US-market power output was only increased to 115 hp. The first- and second-generation engines are very popular with racers and tuners because of their availability, ease of modification, simple design, and lightness.

Third Generation "Red Top" (Smallport)
The third-generation appeared in June 1989 and was in production until June 1991. This engine has the silver cam covers with the words only written in red, hence the nickname "red top". Toyota increased the compression ratio from 9.4:1 to 10.3:1. To correct the air-speed problems of the earlier generations, the intake ports in this cylinder head were re-designed to have a smaller cross-section, and hence it has been nicknamed the "smallport" head. This change in the intake ports negated the need for the earlier twin-runner intake manifold and it was replaced with a single-runner manifold. Additional engine modifications to extend life and reliability included under-piston cooling oil squirters, thicker connecting rods and other components. Also of note, the pistons were changed to utilize a 20 mm fully floating gudgeon pin unlike the 18 mm pressed-in pins of the earlier versions. Other internal revisions were made to the pistons. They were slightly modified to make space for the under-piston cooling oil squirters found in this engine version. In addition to this, the piston ring size were changed to 1.2 mm (top ring), 1.5mm (second ring) and 2.8 mm (oil ring), this change in size made it difficult to obtain as compared to the earlier 16 valves versions of the 4A-GE 1.5 mm (top ring), 1.5 mm (second ring), 3 mm (oil ring). All non-US market 4A-GEs continued to use a MAP sensor, while all of the US-market 4A-GE engines came with a MAF sensor. For US-market cars, this revision increased the power to 125 PS at 7200 rpm with a torque of 15.2 kgm at 4800 rpm. In non-US market cars, this revision produced 140 PS at 7200 rpm and torque at 15 kgm at 4800 rpm.

The 4A-GE engine was first introduced in the 1983 Sprinter Trueno AE86 and the Corolla Levin AE86. The AE86 marked the end of the 4A-GE as a rear wheel drive (RWD or FR) mounted engine. Alongside the RWD AE86/AE85 coupes, a front wheel drive (FWD or FF) Corolla was produced and all future Corollas/Sprinters were based around the FF layout. The AW11 MR2 continued use of the engine as a rear mid-engine, rear-wheel-drive layout, transversely-mounted midship. The engine was retired from North American Corollas in 1991, although it continued to be available in the Geo Prizm GSi (sold through Chevrolet dealerships) from 1990 to 1992. All 4A-GE engines (including the 20-valve versions below) feature a forged crankshaft rather than a cheaper and more commonly used cast version.

Clarification: In the U.S. market, the 4A-GE engine was first used in the 1985 model year Corolla GT-S only, which is identified as an "AE88" in the VIN but uses the AE86 chassis code on the firewall as the AE88 is a "sub" version of the AE86. The 4A-GE engines for the 1985 model year are referred to as "blue top" as opposed to the later "red top" engines, because the paint color on the valve covers is different, to show the different engine revision, using different port sizes, different airflow metering, and other minor differences on the engine.

The American Spec AE86 (VIN AE88, or GT-S) carried the 4A-GE engine. In other markets, other designations were used. Much confusion exists, even among dealers, as to which models contained what equipment, especially since Toyota split the Corolla line into both RWD and FWD versions, and the GT-S designation was only well known as a Celica version at that time.

In 1993, the 4A-GE engine was dropped and replaced with the 7A-FE engine in South Africa even though other countries (except North America) moved towards the newly-developed 20-valve 4A-GE engine, as South African fuel was not suitable at the time for the 20-valve 4A-GE engines. The 20-valve 4A-GE engine would arrive later in the Corolla RXi and RSi in the "black top" revision in 1997.


 * Applications:


 * AA63 Carina 1983.06–1985 (Japan only)
 * AT160 Carina 1985–1988 (Japan only)
 * AT171 Carina 1988–1992 (Japan only)
 * AA63 Celica 1983–1985
 * AT160 Celica 1985–1989
 * AE82 Corolla saloon, FX 1984.10–1987
 * AE86 Corolla Levin 1983.05–1987
 * AE92 Corolla 1987–1993
 * AT141 Corona 1983.10–1985 (Japan only)
 * AT160 Corona 1985–1988 (Japan only)
 * AW11 MR2 1984.06–1989
 * AE82 Sprinter 1984.10–1987 (Japan only)
 * AE86 Sprinter Trueno 1983.05–1987 (Japan only)
 * AE92 Sprinter 1987–1992 (Japan only)
 * AE82/AE92 Corolla GLi Twincam/Conquest RSi 1986–1993 (South Africa)
 * Chevrolet Nova Twin Cam (based on Corolla AE82) 1988
 * Geo Prizm GSi (based on Corolla AE92 chassis) 1990–1992

Fourth Generation "Silver Top"
The fourth-generation 4A-GE engine was produced from 1991 to 1995. It has silver cam covers with chrome lettering, hence the nickname "silver top". This engine yet again features a completely new cylinder head which uses five valves per cylinder instead of four. It uses Toyota's Variable Valve Timing (VVT) system on the intake cam, an increased compression ratio (10.5:1), and the intake system was replaced with a short manifold with individual throttles and velocity stacks, however the vane-type airflow meter was retained, requiring the use of a plenum. The previous 16-valve head used a sharply curved intake port, while the 20-valve engine used a very upright straight port. This engine produces 160 PS at 7,400 rpm with 16.5 kgm of torque at 5,200 rpm.

Applications:
 * AE101 Corolla Levin coupe 1991–1995 (Japan only)
 * AE101 Sprinter Trueno coupe 1991–1995 (Japan only)
 * AE101 Corolla Ceres hardtop 1992–1995 (Japan only)
 * AE101 Sprinter Marino hardtop 1992–1995 (Japan only)
 * AT210 Carina 1996–2001 (Japan only)
 * AE101 Corolla 1991–2000 (Japan only)
 * AE101 Sprinter 1991–2000 (Japan only)



Fifth Generation "Black Top"
The fifth-generation 4A-GE engine produced from 1995 to 2000 is the final version of the 4A-GE engine and has black cam covers. It uses Toyota Variable Valve Timing (VVT) system on the intake cam. This engine is commonly known as the "black top" due to the color of the valve cover, and yet again features an even higher compression ratio (11:1). The air flow sensor was replaced by a MAP sensor, the diameter of the four individual throttle bodies was increased from 43 to 45 mm, the exhaust ports diameter were increased by 3 mm, the intake cam lift was increased from 7.9 to 8.2 mm, and the intake ports were significantly improved in shape and contour, with the width of the opening at the head increased as well. Additionally, the black top had a lighter flywheel, a larger plenum, lighter connecting rods and revised rubber velocity stacks, and was also offered in 1997 with a six-speed C160 transaxle. This revision increased the power to 165 PS at 7,800 rpm with 16.5 kgm of torque at 5,600 rpm. The 'Blacktop' has become a favorite among enthusiasts and is used as an easy power upgrade for the early Toyota Corolla models, especially for use in the drift scene. Due to the relatively high state of tuning of the stock engine, most power/torque gains come from higher lift cams and engine management.

It has been believed that Toyota's power figures for the 20-valve engines are inflated; this statement was more than likely caused by people using less than 100 RON fuel (Japanese premium fuel standard) that both 20-valve engines require.


 * Applications:


 * AE111 Corolla Levin coupe 1995–2000 (Japan only)
 * AE111 Sprinter Trueno coupe 1995–2000 (Japan only)
 * AE101 Corolla Ceres hardtop 1995–1998 (Japan only)
 * AE101 Sprinter Marino hardtop 1995–1998 (Japan only)
 * AE101G Corolla BZ touring wagon 1995–1999 (Japan)
 * AE111 Corolla 1995–2000 (Japan only)
 * AE111 Sprinter 1995–1999 (Japan only)
 * AE111 Sprinter Carib 1997–2000 (Japan only)
 * AE111 Corolla RSi and RXi 1997–2002 (South Africa)
 * AT210 Carina 1996-2001 (Japan only)

4A-GZE


The 4A-GZE was a supercharged version of the 4A-GE produced in various forms from August 1986 through 1995. All three generations shared forged and ceramic coated pistons, a SC12 Roots type supercharger, and uses the stronger 7-rib block and crankshaft as with the 1987–1989 "Late Bigport" second generation 4A-GE.

The 4A-GZE is popular for turbo conversions, as many parts do not need to be modified to support the extra boost.

First Generation
The first generation 4A-GZE produced 8 psi peak manifold pressure. It used dished, forged and coated pistons with an 8.0:1 compression ratio. Compared to the naturally aspirated 4A-GE engine, the only differences for the long block were casting holes for a knock sensor and coolant bypass pipes, lower duration cam timing (232º), the upgraded pistons, different valve covers, and the omission of T-VIS. The first generation 4A-GZE was rated at 145 PS at 6400 rpm and 19.4 kgm at 4400 rpm.

This generation 4A-GZE was first used in the 1986 supercharged Toyota MR2 AW11 until May 1989. It was also used in the 1987–1989 Toyota Corolla AE92 and Sprinter AE92 (Japan-only). Despite having the same specifications, the MR2 was equipped with a distributor and a single ignition coil while the Corolla and Sprinter was equipped with a distributor-less design and twin coil packs.

Applications:
 * AW11 MR2 1986–1989 (Japan, 1988–1989 North America)
 * AE92 Corolla 1987–1989 (Japan only)
 * AE92 Sprinter 1987–1989 (Japan only)

Second Generation
In late 1989, the 4A-GZE was updated with an 8.9:1 compression, and MAP D-Jetronic load sensing and a smaller supercharger pulley producing 10 psi. These updated 4A-GZE engines were rated at 165 PS and 21.2 kgm. This generation can be denoted by a gray cover on the top-mounted intercooler with an emblem reading "Twin Cam 16 Supercharger". While this same gray cover is also used on the early AE92s with the first generation 4A-GZE, the lack of AFM and replacement with MAP in the later AE92s makes the second generation 4A-GZE easily recognizable.

Applications:
 * AE92 Corolla 1989–1991 (Japan only)
 * AE92 Sprinter 1989–1991 (Japan only)

Third Generation
In mid 1991, the 4A-GZE was further upgraded with the "smallport" cylinder head and the block was equipped with piston skirt oil jets for cooling. These minimal updates further increased output to 170 PS and 21.2 kgm. This generation can be denoted by a black cover on the top-mounted intercooler with an emblem featuring Toyota's then-new logo followed by the word "Supercharger".

Applications:
 * AE101 Corolla 1991–1995 (Japan only)
 * AE101 Sprinter 1991–1995 (Japan only)

Racing Applications
Due to its durability, performance and relatively low cost, 4A-GE and 4A-GZE engines and their derivatives have been popular for both professional and amateur racing since their introduction. The most notable application of the 4A-GE in racing was as in the Formula Atlantic series, where in full race trim the engine will produce 250 PS at 10,000 rpm.

5A
The 1498 cc 5A was produced from 1987 through 2006. The carbureted 5A-F was produced in 1987 and the fuel injected 5A-FE was produced that year and again from 1995 through 1998. Both used a cylinder bore and stroke of 78.7x77 mm and had 4 valves per cylinder with DOHC heads using the narrow-valve (22.3°) angle. It uses the same slave-cam system from the 4A-F and 4A-FE.

5A-F
Output for the carb version was 85 PS at 6000 rpm and 12.4 kgm at 3600 rpm.

Applications:
 * AT170 Carina 1988–1990 (Japan only)
 * AE91 Corolla 1987–1989 (Japan only)
 * AT170 Corona 1987–1989 (Japan only)
 * AE91 Sprinter 1987–1989 (Japan only)

5A-FE
Output for the 1987 FI version was 105 PS at 6000 rpm and 13.4 kgm at 4800 rpm. A later one produced 100 PS at 5600 rpm and 14.1 kgm at 4400 rpm.

Toyota joint venture partner Tianjin FAW Xiali produces the 5A-FE (dubbed 5A+) for its Vela and Weizhi (C1) subcompact sedans. This version produces 100 PS at 6000 rpm and 13.3 kgm at 4400 rpm.


 * Applications:


 * Yema SQJ6451
 * Xiali Vela (China)
 * Xiali Weizhi (China)
 * Geely CK (China)
 * Geely MK (China)
 * AT170 Carina 1990–1992 (Japan only)
 * AT192 Carina 1992–1996 (Japan only)
 * AT212 Carina 1996–2001 (Japan only)
 * AE91 Corolla 1989–1992 (Japan only)
 * AE100 Corolla 1991–2001 (Japan only)
 * AE110 Corolla 1995–2000 (Japan only)
 * AE100 Corolla Ceres 1992–1998 (Japan only)
 * AT170 Corona 1989–1992 (Japan only)
 * AL50 Soluna 1996–2003 (Asia)
 * AE91 Sprinter 1989–1992 (Japan only)
 * AE100 Sprinter 1991–1995 (Japan only)
 * AE110 Sprinter 1995–2000(Japan only)
 * AE100 Sprinter Marino 1992–1998 (Japan only)
 * AXP42 Vios 2002–2006 (China only)

5A-FHE
Same as the first generation 5A-FE, only more aggressive tune for more output. Called an EFI-S engine.

This engine produces up to 120 PS due to slightly larger throttle than the standard 5A-FE and different cam profiles.

Applications:
 * AE91 Corolla 1989–1992 (Japan only)
 * AE91 Sprinter 1989–1992 (Japan only)
 * AE91 Toyota G Touring 1994–1999 (Japan only)
 * AE100 Toyota G Touring 1994–1999 (Japan only)

6A
The 1397 cc 6A-FC was produced from 1989 through 1992. It is the only 1.4 variant of the A-series engines. Output is 60 kW and 11.9 kgm.

It is a 4-valve, narrow-valve angle DOHC engine using the slave-cam system, mainly installed in Australian and European market Corollas.

6A-FC
Applications:
 * AE90 Corolla and Holden Nova 1989–1992 (Australia only)

7A
The 1762 cc 7A was produced from 1990 through 2002. Cylinder bore and stroke was 81x85.5 mm. The largest production A-series engine was the 7A-FE, produced from 1993 through 2002. It is a 4-valve DOHC narrow-valve angle economy engine stroked out from the 4A, also reusing the 4A-FE's slave-cam concept. It is a non-interference type engine.

An early Canadian version produced 115 hp at 5600 rpm and 15.2 kgm at 2800 rpm. The common (1993 to 1995 North American) version is rated at 110 hp at 5600 rpm and 15.9 kgm at 2800 rpm. The engine output was changed for the 1996 to 1997 (North American) version mainly due to a different antipollution system and different intake which made it rate at 105 hp at 5200 rpm and 16.2 kgm of torque at 2800 rpm.

In the United States, the 7A-FE's most common application was in the 1993–1997 Corolla (7th generation). The engine was also used in some 1994–1999 Celicas (6th generation) at the base ST trim level, as well as the Toyota Corolla's clone, the Geo Prizm.

The Indonesian and Russian version of the 7A-FE has the strongest naturally aspirated output, with 120 PS at 6000 rpm and 16 kgm at 4400 rpm, with 9.5 compression ratio. It appears in the eighth generation Corolla (AE112).

In the Australian market, the AE112 Corolla Sportivo had a turbocharged and intercooled 7A-FE, sometimes unofficially referred to as a 7A-FTE. Output was 115 kW at 5,600 rpm, torque 24.2 kgm at 3600 rpm, thanks to an IHI RHF4B turbocharger with 0.55 bar of boost pressure. This was a conversion rather than a ground-up turbo design, with the same 9.5:1 compression ratio as the naturally aspirated 7A-FE. Only 110 Corolla Sportivos were built.

Toyota never made a wide-valve angle high-performance engine based on the 7A called the "7A-GE", however many enthusiasts have created one using a combination of 7A-FE parts (block and crank), 4A-GE parts (head, pistons) and custom connecting rods. The 7A-FE has a smaller crank journal and smaller wrist pins (press fit), and so a few companies have made special rods to accommodate these builds. Likewise, an unofficial supercharged "7A-GZE" has also been built from 7A-FE parts (block, crank), 4A-GZE parts (head, pistons) and custom connecting rods.

7A-FE
Applications:
 * AT221 Avensis 1997–2000 (Europe only)
 * AT191 Caldina 1996–1997 (Japan only)
 * AT211 Caldina 1997–2001 (Japan only)
 * AT191 Carina 1994–1996 (Japan only)
 * AT211 Carina 1996–2001 (Japan only)
 * AT191 Carina E 1994–1997 (Europe only)
 * AT200 Celica 1993–1999 (excluding Japan)
 * AE92 Corolla/Conquest September 1993 – circa 1998 (South Africa)
 * AE93 Corolla 1990–1992 (Australia only)
 * AE102/103 Corolla 1992–1998 (excluding Japan)
 * AE102 Corolla/Prizm 1993–1997 (North America)
 * AE111 Corolla 1997–2000 (South Africa)
 * AE111 Corolla 1998–2002 (Brazil)
 * AE112/115 Corolla 1997–2002 (excluding Japan)
 * AE115 Corolla Spacio 1997–2001 (Japan only)
 * AE115 Corolla Linea Terra 1997–1999 (Europe only)
 * AT191 Corona 1994–1997 (excluding Japan)
 * AT211 Corona 1996–2001 (Japan only)
 * AE115 Sprinter Carib 1995–2001 (Japan only)
 * AE112 Corolla 1998–2001 (Indonesia and Australia)

8A
The 1342 cc 8A was produced from 1990 through 2006 by Tianjin FAW Xiali for its Daihatsu and Toyota-based subcompacts. It uses the same cylinder bore of 78.7 mm as the 5A with a reduced stroke of 69 mm and a four valves per cylinder DOHC head with narrow-valve angles. The slave-cam system from the 4A-FE and 5A-FE was retained. Compression ratio is 9.3:1.

Output is 86 hp at 6,000 rpm and 11.2 kgm at 5200 rpm.

8A-FE
Applications:
 * AXP41 Toyota Vios 2002–2006 (China only)
 * AXP41 Xiali Vizi 2002–2006 (China only)
 * Haima CA7130 (China)
 * Xiali 2000/Vela 2000–2012
 * Xiali A+ 2005–2011
 * Xiali Weizhi (China)
 * Etsong Lubao QE6400/QE6440/FAW Lubao CA6410/Jiefang CA6440UA

Production
The 1.3 L and 1.5 L A engines are built in Tianjin FAW Toyota Engine Co., Ltd. Plant No. 1.