Climate change mitigation

Climate change mitigation (or decarbonisation) is action to limit the greenhouse gases in the atmosphere that cause climate change. Climate change mitigation actions include conserving energy and replacing fossil fuels with clean energy sources. Secondary mitigation strategies include changes to land use and removing carbon dioxide (CO2) from the atmosphere. Current climate change mitigation policies are insufficient as they would still result in global warming of about 2.7 °C by 2100, significantly above the 2015 Paris Agreement's goal of limiting global warming to below 2 °C.

Solar energy and wind power can replace fossil fuels at the lowest cost compared to other renewable energy options. The availability of sunshine and wind is variable and can require electrical grid upgrades, such as using long-distance electricity transmission to group a range of power sources. Energy storage can also be used to even out power output, and demand management can limit power use when power generation is low. Cleanly generated electricity can usually replace fossil fuels for powering transportation, heating buildings, and running industrial processes. Certain processes are more difficult to decarbonise, such as air travel and cement production. Carbon capture and storage (CCS) can be an option to reduce net emissions in these circumstances, although fossil fuel power plants with CCS technology is currently a high cost climate change mitigation strategy.

Human land use changes such as agriculture and deforestation cause about 1/4th of climate change. These changes impact how much is absorbed by plant matter and how much organic matter decays or burns to release. These changes are part of the fast carbon cycle, whereas fossil fuels release that was buried underground as part of the slow carbon cycle. Methane is a short lived greenhouse gas that is produced by decaying organic matter and livestock, as well as fossil fuel extraction. Land use changes can also impact precipitation patterns and the reflectivity of the surface of the Earth. It is possible to cut emissions from agriculture by reducing food waste, switching to a more plant-based diet (also referred to as low-carbon diet), and by improving farming processes.

Various policies can encourage climate change mitigation. Carbon pricing systems have been set up that either tax emissions or cap total emissions and trade emission credits. Fossil fuel subsidies can be eliminated in favor of clean energy subsidies, and incentives offered for installing energy efficiency measures or switching to electric power sources. Another issue is overcoming environmental objections when constructing new clean energy sources and making grid modifications.

Definitions and scope
Climate change mitigation aims to sustain ecosystems to maintain human civilisation. This requires drastic cuts in greenhouse gas emissions. The Intergovernmental Panel on Climate Change (IPCC) defines mitigation (of climate change) as "a human intervention to reduce emissions or enhance the sinks of greenhouse gases".

It is possible to approach various mitigation measures in parallel. This is because there is no single pathway to limit global warming to 1.5 or 2 °C. There are four types of measures: The IPCC defined carbon dioxide removal as "Anthropogenic activities removing carbon dioxide from the atmosphere and durably storing it in geological, terrestrial, or ocean reservoirs, or in products. It includes existing and potential anthropogenic enhancement of biological or geochemical  sinks and direct air carbon dioxide capture and storage (DACCS), but excludes natural  uptake not directly caused by human activities."
 * 1) Sustainable energy and sustainable transport
 * 2) Energy conservation, including efficient energy use
 * 3) Sustainable agriculture and green industrial policy
 * 4) Enhancing carbon sinks and carbon dioxide removal (CDR), including carbon sequestration

Relationship with solar radiation modification (SRM)
While solar radiation modification (SRM) could reduce surface temperatures, it temporarily masks climate change rather than addressing the root cause, which is greenhouse gases. SRM would work by altering how much solar radiation the Earth absorbs. Examples include reducing the amount of sunlight reaching the surface, reducing the optical thickness and lifetime of clouds, and changing the ability of the surface to reflect radiation. The IPCC describes SRM as a climate risk reduction strategy or supplementary option rather than a climate mitigation option.

The terminology in this area is still evolving. Experts sometimes use the term geoengineering or climate engineering in the scientific literature for both CDR or SRM, if the techniques are used at a global scale. IPCC reports no longer use the terms geoengineering or climate engineering.

Emission trends and pledges
Greenhouse gas emissions from human activities strengthen the greenhouse effect. This contributes to climate change. Most is carbon dioxide from burning fossil fuels: coal, oil, and natural gas. Human-caused emissions have increased atmospheric carbon dioxide by about 50% over pre-industrial levels. Emissions in the 2010s averaged a record 56 billion tons (Gt) a year. In 2016, energy for electricity, heat and transport was responsible for 73.2% of GHG emissions. Direct industrial processes accounted for 5.2%, waste for 3.2% and agriculture, forestry and land use for 18.4%.

Electricity generation and transport are major emitters. The largest single source is coal-fired power stations with 20% of greenhouse gas emissions. Deforestation and other changes in land use also emit carbon dioxide and methane. The largest sources of anthropogenic methane emissions are agriculture, and gas venting and fugitive emissions from the fossil-fuel industry. The largest agricultural methane source is livestock. Agricultural soils emit nitrous oxide, partly due to fertilizers. There is now a political solution to the problem of fluorinated gases from refrigerants. This is because many countries have ratified the Kigali Amendment.

Carbon dioxide is the dominant emitted greenhouse gas. Methane emissions almost have the same short-term impact. Nitrous oxide (N2O) and fluorinated gases (F-Gases) play a minor role. Livestock and manure produce 5.8% of all greenhouse gas emissions. But this depends on the time frame used to calculate the global warming potential of the respective gas.

Greenhouse gas (GHG) emissions are measured in equivalents. Scientists determine their equivalents from their global warming potential (GWP). This depends on their lifetime in the atmosphere. There are widely used greenhouse gas accounting methods that convert volumes of methane, nitrous oxide and other greenhouse gases to carbon dioxide equivalents. Estimates largely depend on the ability of oceans and land sinks to absorb these gases. Short-lived climate pollutants (SLCPs) persist in the atmosphere for a period ranging from days to 15 years. Carbon dioxide can remain in the atmosphere for millennia. Short-lived climate pollutants include methane, hydrofluorocarbons (HFCs), tropospheric ozone and black carbon.

Scientists increasingly use satellites to locate and measure greenhouse gas emissions and deforestation. Earlier, scientists largely relied on or calculated estimates of greenhouse gas emissions and governments' self-reported data.

Needed emissions cuts
The annual "Emissions Gap Report" by UNEP stated in 2022 that it was necessary to almost halve emissions. "To get on track for limiting global warming to 1.5°C, global annual GHG emissions must be reduced by 45 per cent compared with emissions projections under policies currently in place in just eight years, and they must continue to decline rapidly after 2030, to avoid exhausting the limited remaining atmospheric carbon budget." The report commented that the world should focus on broad-based economy-wide transformations and not incremental change.

In 2022, the Intergovernmental Panel on Climate Change (IPCC) released its Sixth Assessment Report on climate change. It warned that greenhouse gas emissions must peak before 2025 at the latest and decline 43% by 2030 to have a good chance of limiting global warming to 1.5 °C (2.7 °F). Or in the words of Secretary-General of the United Nations António Guterres: "Main emitters must drastically cut emissions starting this year".

Pledges
Climate Action Tracker described the situation on 9 November 2021 as follows. The global temperature will rise by 2.7 °C by the end of the century with current policies and by 2.9 °C with nationally adopted policies. The temperature will rise by 2.4 °C if countries only implement the pledges for 2030. The rise would be 2.1 °C with the achievement of the long-term targets too. Full achievement of all announced targets would mean the rise in global temperature will peak at 1.9 °C and go down to 1.8 °C by the year 2100. Experts gather information about climate pledges in the Global Climate Action Portal - Nazca. The scientific community is checking their fulfilment.

There has not been a definitive or detailed evaluation of most goals set for 2020. But it appears the world failed to meet most or all international goals set for that year.

One update came during the 2021 United Nations Climate Change Conference in Glasgow. The group of researchers running the Climate Action Tracker looked at countries responsible for 85% of greenhouse gas emissions. It found that only four countries or political entities—the EU, UK, Chile and Costa Rica—have published a detailed official policyplan that describes the steps to realise 2030 mitigation targets. These four polities are responsible for 6% of global greenhouse gas emissions.

In 2021 the US and EU launched the Global Methane Pledge to cut methane emissions by 30% by 2030. The UK, Argentina, Indonesia, Italy and Mexico joined the initiative. Ghana and Iraq signaled interest in joining. A White House summary of the meeting noted those countries represent six of the top 15 methane emitters globally. Israel also joined the initiative.

Low-carbon energy


The energy system includes the delivery and use of energy. It is the main emitter of carbon dioxide. Rapid and deep reductions in the carbon dioxide and other greenhouse gas emissions from the energy sector are necessary to limit global warming to well below 2 °C. IPCC recommendations include reducing fossil fuel consumption, increasing production from low- and zero carbon energy sources, and increasing use of electricity and alternative energy carriers.

Nearly all scenarios and strategies involve a major increase in the use of renewable energy in combination with increased energy efficiency measures. It will be necessary to accelerate the deployment of renewable energy six-fold from 0.25% annual growth in 2015 to 1.5% to keep global warming under 2 °C.

The competitiveness of renewable energy is a key to a rapid deployment. In 2020, onshore wind and solar photovoltaics were the cheapest source for new bulk electricity generation in many regions. Renewables may have higher storage costs but non-renewables may have higher clean-up costs. A carbon price can increase the competitiveness of renewable energy.

Solar and wind energy
Wind and sun can provide large amounts of low-carbon energy at competitive production costs. The IPCC estimates that these two mitigation options have the largest potential to reduce emissions before 2030 at low cost.

Solar photovoltaics (PV) has become the cheapest way to generate electricity in many regions of the world. The growth of photovoltaics has been close to exponential. It has about doubled every three years since the 1990s. A different technology is concentrated solar power (CSP). This uses mirrors or lenses to concentrate a large area of sunlight on to a receiver. With CSP, the energy can be stored for a few hours. This provides supply in the evening. Solar water heating doubled between 2010 and 2019. Regions in the higher northern and southern latitudes have the greatest potential for wind power. Offshore wind farms are more expensive. But offshore units deliver more energy per installed capacity with less fluctuations. In most regions, wind power generation is higher in the winter when PV output is low. For this reason, combinations of wind and solar power lead to better-balanced systems.

Other renewables
Other well-established renewable energy forms include hydropower, bioenergy and geothermal energy.
 * Hydroelectricity is electricity generated by hydropower and plays a leading role in countries like Brazil, Norway and China. but there are geographical limits and environmental issues. Tidal power can be used in coastal regions.
 * Bioenergy can provide energy for electricity, heat and transport. Bioenergy, in particular biogas, can provide dispatchable electricity generation. While burning plant-derived biomass releases, the plants withdraw from the atmosphere while they grow. The technologies for producing, transporting and processing a fuel have a significant impact on the lifecycle emissions of the fuel. For example, aviation is starting to use renewable biofuels.
 * Geothermal power is electrical power generated from geothermal energy. Geothermal electricity generation is currently used in 26 countries. Geothermal heating is in use in 70 countries.

Integrating variable renewable energy
Wind and solar power production does not consistently match demand. To deliver reliable electricity from variable renewable energy sources such as wind and solar, electrical power systems must be flexible. Most electrical grids were constructed for non-intermittent energy sources such as coal-fired power plants. The integration of larger amounts of solar and wind energy into the grid requires a change of the energy system; this is necessary to ensure that the supply of electricity matches demand.

There are various ways to make the electricity system more flexible. In many places, wind and solar generation are complementary on a daily and a seasonal scale. There is more wind during the night and in winter when solar energy production is low. Linking different geographical regions through long-distance transmission lines also makes it possible to reduce variability. It is possible to shift energy demand in time. Energy demand management and the use of smart grids make it possible to match the times when variable energy production is highest. Sector coupling can provide further flexibility. This involves coupling the electricity sector to the heat and mobility sector via power-to-heat-systems and electric vehicles. Energy storage helps overcome barriers to intermittent renewable energy. The most commonly used and available storage method is pumped-storage hydroelectricity. This requires locations with large differences in height and access to water. Batteries are also in wide use. They typically store electricity for short periods. Batteries have low energy density. This and their cost makes them impractical for the large energy storage necessary to balance inter-seasonal variations in energy production. Some locations have implemented pumped hydro storage with capacity for multi-month usage.

Nuclear power
Nuclear power could complement renewables for electricity. On the other hand, environmental and security risks could outweigh the benefits.

The construction of new nuclear reactors currently takes about 10 years. This is much longer than scaling up the deployment of wind and solar. And this timing gives rise to credit risks. However nuclear may be much cheaper in China. China is building a significant number of new power plants. the cost of extending nuclear power plant lifetimes is competitive with other electricity generation technologies if long term costs for nuclear waste disposal are excluded from the calculation. There is also no sufficient financial insurance for nuclear accidents.

Demand reduction
Reducing demand for products and services that cause greenhouse gas emissions can help in mitigating climate change. One is to reduce demand by behavioural and cultural changes, for example by making changes in diet, especially the decision to reduce meat consumption, an effective action individuals take to fight climate change. Another is by reducing the demand by improving infrastructure, by building a good public transport network, for example. Lastly, changes in end-use technology can reduce energy demand. For instance a well-insulated house emits less than a poorly-insulated house.

Mitigation options that reduce demand for products or services help people make personal choices to reduce their carbon footprint. This could be in their choice of transport or food. So these mitigation options have many social aspects that focus on demand reduction; they are therefore demand-side mitigation actions. For example, people with high socio-economic status often cause more greenhouse gas emissions than those from a lower status. If they reduce their emissions and promote green policies, these people could become low-carbon lifestyle role models. However, there are many psychological variables that influence consumers. These include awareness and perceived risk.

Government policies can support or hinder demand-side mitigation options. For example, public policy can promote circular economy concepts which would support climate change mitigation. Reducing greenhouse gas emissions is linked to the sharing economy.

There is a debate regarding the correlation of economic growth and emissions. It seems economic growth no longer necessarily means higher emissions.

Energy conservation and efficiency
Global primary energy demand exceeded 161,000 terawatt hours (TWh) in 2018. This refers to electricity, transport and heating including all losses. In transport and electricity production, fossil fuel usage has a low efficiency of less than 50%. Large amounts of heat in power plants and in motors of vehicles go to waste. The actual amount of energy consumed is significantly lower at 116,000 TWh.

Energy conservation is the effort made to reduce the consumption of energy by using less of an energy service. One way is to use energy more efficiently. This means using less energy than before to produce the same service. Another way is to reduce the amount of service used. An example of this would be to drive less. Energy conservation is at the top of the sustainable energy hierarchy. When consumers reduce wastage and losses they can conserve energy. The upgrading of technology as well as the improvements to operations and maintenance can result in overall efficiency improvements.

Efficient energy use (or energy efficiency) is the process of reducing the amount of energy required to provide products and services. Improved energy efficiency in buildings ("green buildings"), industrial processes and transportation could reduce the world's energy needs in 2050 by one third. This would help reduce global emissions of greenhouse gases. For example, insulating a building allows it to use less heating and cooling energy to achieve and maintain thermal comfort. Improvements in energy efficiency are generally achieved by adopting a more efficient technology or production process. Another way is to use commonly accepted methods to reduce energy losses.

Lifestyle changes
Individual action on climate change can include personal choices in many areas. These include diet, travel, household energy use, consumption of goods and services, and family size. People who wish to reduce their carbon footprint can take high-impact actions such as avoiding frequent flying and petrol-fuelled cars, eating mainly a plant-based diet, having fewer children, using clothes and electrical products for longer, and electrifying homes. These approaches are more practical for people in high-income countries with high-consumption lifestyles. Naturally, it is more difficult for those with lower income statuses to make these changes. This is because choices like electric-powered cars may not be available. Excessive consumption is more to blame for climate change than population increase. High-consumption lifestyles have a greater environmental impact, with the richest 10% of people emitting about half the total lifestyle emissions.

Dietary change
Some scientists say that avoiding meat and dairy foods is the single biggest way an individual can reduce their environmental impact. The widespread adoption of a vegetarian diet could cut food-related greenhouse gas emissions by 63% by 2050. China introduced new dietary guidelines in 2016 which aim to cut meat consumption by 50% and thereby reduce greenhouse gas emissions by 1Gt per year by 2030. Overall, food accounts for the largest share of consumption-based greenhouse gas emissions. It is responsible for nearly 20% of the global carbon footprint. Almost 15% of all anthropogenic greenhouse gas emissions have been attributed to the livestock sector.

A shift towards plant-based diets would help to mitigate climate change. In particular, reducing meat consumption would help to reduce methane emissions. If high-income nations switched to a plant-based diet, vast amounts of land used for animal agriculture could be allowed to return to their natural state. This in turn has the potential to sequester 100 billion tonnes of by the end of the century. A comprehensive analysis found that plant based diets reduce emissions, water pollution and land use significantly (by 75%), while reducing the destruction of wildlife and usage of water.

Family size
Population growth has resulted in higher greenhouse gas emissions in most regions, particularly Africa. However, economic growth has a bigger effect than population growth. Rising incomes, changes in consumption and dietary patterns, as well as population growth, cause pressure on land and other natural resources. This leads to more greenhouse gas emissions and fewer carbon sinks. Some scholars have argued that humane policies to slow population growth should be part of a broad climate response together with policies that end fossil fuel use and encourage sustainable consumption. Advances in female education and reproductive health, especially voluntary family planning, can contribute to reducing population growth.

Preserving and enhancing carbon sinks


An important mitigation measure is "preserving and enhancing carbon sinks". This refers to the management of Earth's natural carbon sinks in a way that preserves or increases their capability to remove CO2 from the atmosphere and to store it durably. Scientists call this process also carbon sequestration. In the context of climate change mitigation, the IPCC defines a sink as "Any process, activity or mechanism which removes a greenhouse gas, an aerosol or a precursor of a greenhouse gas from the atmosphere". Globally, the two most important carbon sinks are vegetation and the ocean.

To enhance the ability of ecosystems to sequester carbon, changes are necessary in agriculture and forestry. Examples are preventing deforestation and restoring natural ecosystems by reforestation. Scenarios that limit global warming to 1.5 °C typically project the large-scale use of carbon dioxide removal methods over the 21st century. There are concerns about over-reliance on these technologies, and their environmental impacts. But ecosystem restoration and reduced conversion are among the mitigation tools that can yield the most emissions reductions before 2030.

Land-based mitigation options are referred to as "AFOLU mitigation options" in the 2022 IPCC report on mitigation. The abbreviation stands for "agriculture, forestry and other land use" The report described the economic mitigation potential from relevant activities around forests and ecosystems as follows: "the conservation, improved management, and restoration of forests and other ecosystems (coastal wetlands, peatlands, savannas and grasslands)". A high mitigation potential is found for reducing deforestation in tropical regions. The economic potential of these activities has been estimated to be 4.2 to 7.4 gigatonnes of carbon dioxide equivalent (GtCO2 -eq) per year.

Conservation
The Stern Review on the economics of climate change stated in 2007 that curbing deforestation was a highly cost-effective way of reducing greenhouse gas emissions. About 95% of deforestation occurs in the tropics, where clearing of land for agriculture is one of the main causes. One forest conservation strategy is to transfer rights over land from public ownership to its indigenous inhabitants. Land concessions often go to powerful extractive companies. Conservation strategies that exclude and even evict humans, called fortress conservation, often lead to more exploitation of the land. This is because the native inhabitants turn to work for extractive companies to survive.

Proforestation is promoting forests to capture their full ecological potential. This is a mitigation strategy as secondary forests that have regrown in abandoned farmland are found to have less biodiversity than the original old-growth forests. Original forests store 60% more carbon than these new forests. Strategies include rewilding and establishing wildlife corridors.

Afforestation and reforestation
Afforestation is the establishment of trees where there was previously no tree cover. Scenarios for new plantations covering up to 4000 million hectares (Mha) (6300 x 6300 km) suggest cumulative carbon storage of more than 900 GtC (2300 Gt) until 2100. But they are not a viable alternative to aggressive emissions reduction. This is because the plantations would need to be so large they would eliminate most natural ecosystems or reduce food production. One example is the Trillion Tree Campaign. However, preserving biodiversity is also important and for example not all grasslands are suitable for conversion into forests. Grasslands can even turn from carbon sinks to carbon sources.

Reforestation is the restocking of existing depleted forests or in places where there were recently forests. Reforestation could save at least 1GtCO2 per year, at an estimated cost of $5–15 per tonne of carbon dioxide (tCO2). Restoring all degraded forests all over the world could capture about 205 GtC (750 Gt). With increased intensive agriculture and urbanization, there is an increase in the amount of abandoned farmland. By some estimates, for every acre of original old-growth forest cut down, more than 50 acres of new secondary forests are growing. In some countries, promoting regrowth on abandoned farmland could offset years of emissions.

Planting new trees can be expensive and a risky investment. For example, about 80 percent of planted trees in the Sahel die within two years. Reforestation has higher carbon storage potential than afforestation. Even long-deforested areas still contain an "underground forest" of living roots and tree stumps. Helping native species sprout naturally is cheaper than planting new trees and they are more likely to survive. This could include pruning and coppicing to accelerate growth. This also provides woodfuel, which is otherwise a major source of deforestation. Such practices, called farmer-managed natural regeneration, are centuries old but the biggest obstacle towards implementation is ownership of the trees by the state. The state often sells timber rights to businesses which leads to locals uprooting seedlings because they see them as a liability. Legal aid for locals and changes to property law such as in Mali and Niger have led to significant changes. Scientists describe them as the largest positive environmental transformation in Africa. It is possible to discern from space the border between Niger and the more barren land in Nigeria, where the law has not changed.

Soils
There are many measures to increase soil carbon. This makes it complex and hard to measure and account for. One advantage is that there are fewer trade-offs for these measures than for BECCS or afforestation, for example.

Globally, protecting healthy soils and restoring the soil carbon sponge could remove 7.6 billion tonnes of carbon dioxide from the atmosphere annually. This is more than the annual emissions of the US. Trees capture while growing above ground and exuding larger amounts of carbon below ground. Trees contribute to the building of a soil carbon sponge. Carbon formed above ground is released as immediately when wood is burned. If dead wood remains untouched, only some of the carbon returns to the atmosphere as decomposition proceeds.

Farming can deplete soil carbon and render soil incapable of supporting life. However, conservation farming can protect carbon in soils, and repair damage over time. The farming practice of cover crops is a form of carbon farming. Methods that enhance carbon sequestration in soil include no-till farming, residue mulching and crop rotation. Scientists have described the best management practices for European soils to increase soil organic carbon. These are conversion of arable land to grassland, straw incorporation, reduced tillage, straw incorporation combined with reduced tillage, ley cropping system and cover crops.

Another mitigation option is the production of biochar and its storage in soils This is the solid material that remains after the pyrolysis of biomass. Biochar production releases half of the carbon from the biomass—either released into the atmosphere or captured with CCS—and retains the other half in the stable biochar. It can endure in soil for thousands of years. Biochar may increase the soil fertility of acidic soils and increase agricultural productivity. During production of biochar, heat is released which may be used as bioenergy.

Wetlands
Wetland restoration is an important mitigation measure. It has moderate to great mitigation potential on a limited land area with low trade-offs and costs. Wetlands perform two important functions in relation to climate change. They can sequester carbon, converting carbon dioxide to solid plant material through photosynthesis. They also store and regulate water. Wetlands store about 45 million tonnes of carbon per year globally.

Some wetlands are a significant source of methane emissions. Some also emit nitrous oxide. Peatland globally covers just 3% of the land's surface. But it stores up to 550 gigatonnes (Gt) of carbon. This represents 42% of all soil carbon and exceeds the carbon stored in all other vegetation types, including the world's forests. The threat to peatlands includes draining the areas for agriculture. Another threat is cutting down trees for lumber, as the trees help hold and fix the peatland. Additionally, peat is often sold for compost. It is possible to restore degraded peatlands by blocking drainage channels in the peatland, and allowing natural vegetation to recover.

Mangroves, salt marshes and seagrasses make up the majority of the ocean's vegetated habitats. They only equal 0.05% of the plant biomass on land. But they store carbon 40 times faster than tropical forests. Bottom trawling, dredging for coastal development and fertilizer runoff have damaged coastal habitats. Notably, 85% of oyster reefs globally have been removed in the last two centuries. Oyster reefs clean the water and help other species thrive. This increases biomass in that area. In addition, oyster reefs mitigate the effects of climate change by reducing the force of waves from hurricanes. They also reduce the erosion from rising sea levels. Restoration of coastal wetlands is thought to be more cost-effective than restoration of inland wetlands.

Deep ocean
These options focus on the carbon which ocean reservoirs can store. They include ocean fertilization, ocean alkalinity enhancement or enhanced weathering. The IPCC found in 2022 ocean-based mitigation options currently have only limited deployment potential. But it assessed that their future mitigation potential is large. It found that in total, ocean-based methods could remove 1–100 Gt of per year. Their costs are in the order of US$40–500 per tonne of. Most of these options could also help to reduce ocean acidification. This is the drop in pH value caused by increased atmospheric CO2 concentrations.

Blue carbon management is another type of ocean-based biological carbon dioxide removal (CDR). It can involve land-based as well as ocean-based measures. The term usually refers to the role that tidal marshes, mangroves and seagrasses can play in carbon sequestration. Some of these efforts can also take place in deep ocean waters. This is where the vast majority of ocean carbon is held. These ecosystems can contribute to climate change mitigation and also to ecosystem-based adaptation. Conversely, when blue carbon ecosystems are degraded or lost they release carbon back to the atmosphere. There is increasing interest in developing blue carbon potential. Scientists have found that in some cases these types of ecosystems remove far more carbon per area than terrestrial forests. However, the long-term effectiveness of blue carbon as a carbon dioxide removal solution remains under discussion.

Enhanced weathering
Enhanced weathering could remove 2–4 Gt of per year. This process aims to accelerate natural weathering by spreading finely ground silicate rock, such as basalt, onto surfaces. This speeds up chemical reactions between rocks, water, and air. It removes carbon dioxide from the atmosphere, permanently storing it in solid carbonate minerals or ocean alkalinity. Cost estimates are in the US$50–200 per tonne range of.

Other methods to capture and store CO2


In addition to traditional land-based methods to remove carbon dioxide (CO2) from the air, other technologies are under development. These could reduce CO2 emissions and lower existing atmospheric CO2 levels. Carbon capture and storage (CCS) is a method to mitigate climate change by capturing CO2 from large point sources, such as cement factories or biomass power plants. It then stores it away safely instead of releasing it into the atmosphere. The IPCC estimates that the costs of halting global warming would double without CCS.

Bioenergy with carbon capture and storage (BECCS) expands on the potential of CCS and aims to lower atmospheric CO2 levels. This process uses biomass grown for bioenergy. The biomass yields energy in useful forms such as electricity, heat, biofuels, etc. through consumption of the biomass via combustion, fermentation, or pyrolysis. The process captures the CO2 that was extracted from the atmosphere when it grew. It then stores it underground or via land application as biochar. This effectively removes it from the atmosphere. This makes BECCS a negative emissions technology (NET).

Scientists estimated the potential range of negative emissions from BECCS in 2018 as 0–22 Gt per year. , BECCS was capturing approximately 2 million tonnes per year of CO2 annually. The cost and availability of biomass limits wide deployment of BECCS. BECCS currently forms a big part of achieving climate targets beyond 2050 in modelling, such as by the Integrated Assessment Models (IAMs) associated with the IPCC process. But many scientists are sceptical due to the risk of loss of biodiversity.

Direct air capture is a process of capturing directly from the ambient air. This is in contrast to CCS which captures carbon from point sources. It generates a concentrated stream of for sequestration, utilization or production of carbon-neutral fuel and windgas. Artificial processes vary, and there are concerns about the long-term effects of some of these processes.

Buildings
The building sector accounts for 23% of global energy-related emissions. About half of the energy is used for space and water heating. Building insulation can reduce the primary energy demand significantly. Heat pump loads may also provide a flexible resource that can participate in demand response to integrate variable renewable resources into the grid. Solar water heating uses thermal energy directly. Sufficiency measures include moving to smaller houses when the needs of households change, mixed use of spaces and the collective use of devices. Planners and civil engineers can construct new buildings using passive solar building design, low-energy building, or zero-energy building techniques. In addition, it is possible to design buildings that are more energy-efficient to cool by using lighter-coloured, more reflective materials in the development of urban areas.

Heat pumps efficiently heat buildings, and cool them by air conditioning. A modern heat pump typically transports around three to five times more thermal energy than electrical energy consumed. The amount depends on the coefficient of performance and the outside temperature.

Refrigeration and air conditioning account for about 10% of global emissions caused by fossil fuel-based energy production and the use of fluorinated gases. Alternative cooling systems, such as passive cooling building design and passive daytime radiative cooling surfaces, can reduce air conditioning use. Suburbs and cities in hot and arid climates can significantly reduce energy consumption from cooling with daytime radiative cooling.

Energy consumption for cooling is likely to rise significantly due to increasing heat and availability of devices in poorer countries. Of the 2.8 billion people living in the hottest parts of the world, only 8% currently have air conditioners, compared with 90% of people in the US and Japan. Adoption of air conditioners typically increases in warmer areas at above $10,000 annual household income. By combining energy efficiency improvements and decarbonising electricity for air conditioning with the transition away from super-polluting refrigerants, the world could avoid cumulative greenhouse gas emissions of up to 210–460 Gt-eq over the next four decades. A shift to renewable energy in the cooling sector comes with two advantages: Solar energy production with mid-day peaks corresponds with the load required for cooling and additionally, cooling has a large potential for load management in the electric grid.

Urban planning


Cities emitted 28 GtCO2-eq in 2020 of combined CO2 and emissions. This was from producing and consuming goods and services. Climate-smart urban planning aims to reduce sprawl to reduce the distance travelled. This lowers emissions from transportation. Switching from cars by improving walkability and cycling infrastructure is beneficial to a country's economy as a whole.

Urban forestry, lakes and other blue and green infrastructure can reduce emissions directly and indirectly by reducing energy demand for cooling. Methane emissions from municipal solid waste can be reduced by segregation, composting, and recycling.

Transport
Transportation accounts for 15% of emissions worldwide. Increasing the use of public transport, low-carbon freight transport and cycling are important components of transport decarbonisation.

Electric vehicles and environmentally friendly rail help to reduce the consumption of fossil fuels. In most cases, electric trains are more efficient than air transport and truck transport. Other efficiency means include improved public transport, smart mobility, carsharing and electric hybrids. Fossil-fuel for passenger cars can be included in emissions trading. Furthermore, moving away from a car-dominated transport system towards low-carbon advanced public transport system is important.

Heavyweight, large personal vehicles (such as cars) require a lot of energy to move and take up much urban space. Several alternatives modes of transport are available to replace these. The European Union has made smart mobility part of its European Green Deal. In smart cities, smart mobility is also important. The World Bank is helping lower income countries buy electric buses. Their purchase price is higher than diesel buses. But lower running costs and health improvements due to cleaner air can offset this higher price.

Between one quarter and three quarters of cars on the road by 2050 are forecast to be electric vehicles. Hydrogen may be a solution for long-distance heavy freight trucks, if batteries alone are too heavy.

Shipping
In the shipping industry, the use of liquefied natural gas (LNG) as a marine bunker fuel is driven by emissions regulations. Ship operators must switch from heavy fuel oil to more expensive oil-based fuels, implement costly flue gas treatment technologies or switch to LNG engines. Methane slip, when gas leaks unburned through the engine, lowers the advantages of LNG. Maersk, the world's biggest container shipping line and vessel operator, warns of stranded assets when investing in transitional fuels like LNG. The company lists green ammonia as one of the preferred fuel types of the future. It has announced the first carbon-neutral vessel on the water by 2023, running on carbon-neutral methanol. Cruise operators are trialling partially hydrogen-powered ships.

Hybrid and all electric ferries are suitable for short distances. Norway's goal is an all electric fleet by 2025.

Air transport


Jet airliners contribute to climate change by emitting carbon dioxide, nitrogen oxides, contrails and particulates. Their radiative forcing is estimated at 1.3–1.4 that of alone, excluding induced cirrus cloud. In 2018, global commercial operations generated 2.4% of all emissions.

The aviation industry has become more fuel efficient. But overall emissions have risen as the volume of air travel has increased. By 2020, aviation emissions were 70% higher than in 2005 and they could grow by 300% by 2050.

It is possible to reduce aviation's environmental footprint by better fuel economy in aircraft. Optimising flight routes to lower non- effects on climate from nitrogen oxides, particulates or contrails can also help. Aviation biofuel, carbon emission trading and carbon offsetting, part of the 191 nation ICAO's Carbon Offsetting and Reduction Scheme for International Aviation (CORSIA), can lower emissions. Short-haul flight bans, train connections, personal choices and taxation on flights can lead to fewer flights. Hybrid electric aircraft and electric aircraft or hydrogen-powered aircraft may replace fossil fuel-powered aircraft.

Experts expect emissions from aviation to rise in most projections, at least until 2040. They currently amount to 180 Mt of or 11% of transport emissions. Aviation biofuel and hydrogen can only cover a small proportion of flights in the coming years. Experts expect hybrid-driven aircraft to start commercial regional scheduled flights after 2030. Battery-powered aircraft are likely to enter the market after 2035. Under CORSIA, flight operators can purchase carbon offsets to cover their emissions above 2019 levels. CORSIA will be compulsory from 2027.

Agriculture, forestry and land use


Almost 20% of greenhouse gas emissions come from the agriculture and forestry sector. To significantly reduce these emissions, annual investments in the agriculture sector need to increase to $260 billion by 2030. The potential benefits from these investments are estimated at about $4.3 trillion by 2030, offering a substantial economic return of 16-to-1.

Mitigation measures in the food system can be divided into four categories. These are demand-side changes, ecosystem protections, mitigation on farms, and mitigation in supply chains. On the demand side, limiting food waste is an effective way to reduce food emissions. Changes to a diet less reliant on animal products such as plant-based diets are also effective.

With 21% of global methane emissions, cattle are a major driver of global warming. When rainforests are cut and the land is converted for grazing, the impact is even higher. In Brazil, producing 1 kg of beef can result in the emission of up to 335 kg CO2-eq. Other livestock, manure management and rice cultivation also emit greenhouse gases, in addition to fossil fuel combustion in agriculture.

Important mitigation options for reducing the greenhouse gas emissions from livestock include genetic selection, introduction of methanotrophic bacteria into the rumen,  vaccines, feeds, diet modification and grazing management. Other options are diet changes towards ruminant-free alternatives, such as milk substitutes and meat analogues. Non-ruminant livestock, such as poultry, emit far fewer GHGs.

It is possible to cut methane emissions in rice cultivation by improved water management, combining dry seeding and one drawdown, or executing a sequence of wetting and drying. This results in emission reductions of up to 90% compared to full flooding and even increased yields.

Industry
Industry is the largest emitter of greenhouse gases when direct and indirect emissions are included. Electrification can reduce emissions from industry. Green hydrogen can play a major role in energy-intensive industries for which electricity is not an option. Further mitigation options involve the steel and cement industry, which can switch to a less polluting production process. Products can be made with less material to reduce emission-intensity and industrial processes can be made more efficient. Finally, circular economy measures reduce the need for new materials. This also saves on emissions that would have been released from the mining of collecting of those materials.

The decarbonisation of cement production requires new technologies, and therefore investment in innovation. Bioconcrete is one possibility to reduce emissions. But no technology for mitigation is yet mature. So CCS will be necessary at least in the short-term.

Another sector with a significant carbon footprint is the steel sector, which is responsible for about 7% of global emissions. Emissions can be reduced by using electric arc furnaces to melt and recycle scrap steel. To produce virgin steel without emissions, blast furnaces could be replaced by hydrogen direct reduced iron and electric arc furnaces. Alternatively, carbon capture and storage solutions can be used.

Coal, gas and oil production often come with significant methane leakage. In the early 2020s some governments recognized the scale of the problem and introduced regulations. Methane leaks at oil and gas wells and processing plants are cost-effective to fix in countries which can easily trade gas internationally. There are leaks in countries where gas is cheap; such as Iran, Russia, and Turkmenistan. Nearly all this can be stopped by replacing old components and preventing routine flaring. Coalbed methane may continue leaking even after the mine has been closed. But it can be captured by drainage and/or ventilation systems. Fossil fuel firms do not always have financial incentives to tackle methane leakage.

Co-benefits
Co-benefits of climate change mitigation, also often referred to as ancillary benefits, were firstly dominated in the scientific literature by studies that describe how lower GHG emissions lead to better air quality and consequently impact human health positively. The scope of co-benefits research expanded to its economic, social, ecological and political implications.

Positive secondary effects that occur from climate mitigation and adaptation measures have been mentioned in research since the 1990s. The IPCC first mentioned the role of co-benefits in 2001, followed by its fourth and fifth assessment cycle stressing improved working environment, reduced waste, health benefits and reduced capital expenditures. In the early 2000s the OECD was further fostering its efforts in promoting ancillary benefits.

The IPCC pointed out in 2007: "Co-benefits of GHG mitigation can be an important decision criteria in analyses carried out by policy-makers, but they are often neglected" and added that the co-benefits are "not quantified, monetised or even identified by businesses and decision-makers". Appropriate consideration of co-benefits can greatly "influence policy decisions concerning the timing and level of mitigation action", and there can be "significant advantages to the national economy and technical innovation".

Employment and economic development
Co-benefits can positively impact employment, industrial development, states' energy independence and energy self-consumption. The deployment of renewable energies can foster job opportunities. Depending on the country and deployment scenario, replacing coal power plants with renewable energy can more than double the number of jobs per average MW capacity. Investments in renewable energies, especially in solar- and wind energy, can boost the value of production. Countries which rely on energy imports can enhance their energy independence and ensure supply security by deploying renewables. National energy generation from renewables lowers the demand for fossil fuel imports which scales up annual economic saving.

Energy security
A higher share of renewables can additionally lead to more energy security. Socioeconomic co-benefits have been analysed such as energy access in rural areas and improved rural livelihoods. Rural areas which are not fully electrified can benefit from the deployment of renewable energies. Solar-powered mini-grids can remain economically viable, cost-competitive and reduce the number of power cuts. Energy reliability has additional social implications: stable electricity improves the quality of education.

The International Energy Agency (IEA) spelled out the "multiple benefits approach" of energy efficiency while the International Renewable Energy Agency (IRENA) operationalised the list of co-benefits of the renewable energy sector.

Health and well-being
The health benefits from climate change mitigation are significant. Potential measures can not only mitigate future health impacts from climate change but also improve health directly. Climate change mitigation is interconnected with various health co-benefits, such as those from reduced air pollution. Air pollution generated by fossil fuel combustion is both a major driver of global warming and the cause of a large number of annual deaths. Some estimates are as high as 8.7 million excess deaths during 2018. Mitigation policies can also promote healthier diets such as less red meat, more active lifestyles, and increased exposure to green urban spaces. Access to urban green spaces provides benefits to mental health as well. The increased use of green and blue infrastructure can reduce the urban heat island effect. This reduces heat stress on people.

Climate change adaptation
Some mitigation measures have co-benefits in the area of climate change adaptation. This is for example the case for many nature-based solutions. Examples in the urban context include urban green and blue infrastructure which provide mitigation as well as adaptation benefits. This can be in the form of urban forests and street trees, green roofs and walls, urban agriculture and so forth. The mitigation is achieved through the conservation and expansion of carbon sinks and reduced energy use of buildings. Adaptation benefits come for example through reduced heat stress and flooding risk.



Negative side effects
Mitigation measures can also have negative side effects and risks. In agriculture and forestry, mitigation measures can affect biodiversity and ecosystem functioning. In renewable energy, mining for metals and minerals can increase threats to conservation areas. There is some research into ways to recycle solar panels and electronic waste. This would create a source for materials so there is no need to mine them.

Scholars have found that discussions about risks and negative side effects of mitigation measures can lead to deadlock or the feeling that there are insuperable barriers to taking action.

Costs and funding
Several factors affect mitigation cost estimates. One is the baseline. This is a reference scenario that the alternative mitigation scenario is compared with. Others are the way costs are modelled, and assumptions about future government policy. Cost estimates for mitigation for specific regions depend on the quantity of emissions allowed for that region in future, as well as the timing of interventions.

Mitigation costs will vary according to how and when emissions are cut. Early, well-planned action will minimize the costs. Globally, the benefits of keeping warming under 2 °C exceed the costs.

Economists estimate the cost of climate change mitigation at between 1% and 2% of GDP. While this is a large sum, it is still far less than the subsidies governments provide to the ailing fossil fuel industry. The International Monetary Fund estimated this at more than $5 trillion per year.

Another estimate says that financial flows for climate mitigation and adaptation are going to be over $800 billion per year. These financial requirements are predicted to exceed $4 trillion per year by 2030.

Globally, limiting warming to 2 °C may result in higher economic benefits than economic costs. The economic repercussions of mitigation vary widely across regions and households, depending on policy design and level of international cooperation. Delayed global cooperation increases policy costs across regions, especially in those that are relatively carbon intensive at present. Pathways with uniform carbon values show higher mitigation costs in more carbon-intensive regions, in fossil-fuels exporting regions and in poorer regions. Aggregate quantifications expressed in GDP or monetary terms undervalue the economic effects on households in poorer countries. The actual effects on welfare and well-being are comparatively larger.

Cost–benefit analysis may be unsuitable for analysing climate change mitigation as a whole. But it is still useful for analysing the difference between a 1.5 °C target and 2 °C. One way of estimating the cost of reducing emissions is by considering the likely costs of potential technological and output changes. Policymakers can compare the marginal abatement costs of different methods to assess the cost and amount of possible abatement over time. The marginal abatement costs of the various measures will differ by country, by sector, and over time.

Avoided costs of climate change effects
It is possible to avoid some of the costs of the effects of climate change by limiting climate change. According to the Stern Review, inaction can be as high as the equivalent of losing at least 5% of global gross domestic product (GDP) each year, now and forever. This can be up to 20% of GDP or more when including a wider range of risks and impacts. But mitigating climate change will only cost about 2% of GDP. Also it may not be a good idea from a financial perspective to delay significant reductions in greenhouse gas emissions.

Mitigation solutions are often evaluated in terms of costs and greenhouse gas reduction potentials. This fails to take into account the direct effects on human well-being.

Distributing emissions abatement costs
Mitigation at the speed and scale required to limit warming to 2 °C or below implies deep economic and structural changes. These raise multiple types of distributional concerns across regions, income classes and sectors.

There have been different proposals on how to allocate responsibility for cutting emissions. These include egalitarianism, basic needs according to a minimum level of consumption, proportionality and the polluter-pays principle. A specific proposal is "equal per capita entitlements". This approach has two categories. In the first category, emissions are allocated according to national population. In the second category, emissions are allocated in a way that attempts to account for historical or cumulative emissions.

Funding
In order to reconcile economic development with mitigating carbon emissions, developing countries need particular support. This would be both financial and technical. The IPCC found that accelerated support would also tackle inequities in financial and economic vulnerability to climate change. One way to achieve this is the Kyoto Protocol's Clean Development Mechanism (CDM).

National policies
Climate change mitigation policies can have a large and complex impact on the socio-economic status of individuals and countries This can be both positive and negative. It is important to design policies well and make them inclusive. Otherwise climate change mitigation measures can impose higher financial costs on poor households.

The most effective and economically efficient approach of achieving lower emissions in the energy sector is to apply a combination of measures. These include market-based instruments such as taxes and permits, standards, and information policies.

Types of national policies that would support climate change mitigation include:
 * Removing unhelpful subsidies: Many countries provide subsidies for activities that affect emissions. For example, significant fossil fuel subsidies are present in many countries. Phasing-out fossil fuel subsidies is crucial to address the climate crisis. It must however be done carefully to avoid protests and making poor people poorer.
 * Regulatory standards: These set technology or performance standards. They can be effective in addressing the market failure of informational barriers. If the costs of regulation are less than the benefits of addressing the market failure, standards can result in net benefits.
 * Market-based instruments such as emission taxes and charges. An emissions tax requires domestic emitters to pay a fixed fee or tax for every tonne of CO2-eq GHG emissions they release into the atmosphere. If every emitter were to face the same level of tax, emitters would choose the lowest cost way of achieving emission reductions first. In the real world, however, markets are not perfect. This means that an emissions tax may deviate from this ideal. Distributional and equity considerations usually result in differential tax rates for different sources.
 * Tradable permits: A permit system can limit emissions. A number of permits are distributed equal to the emission limit. Each liable entity must hold the number of permits equal to its actual emissions. A tradable permit system can be cost-effective if costs are not excessive. There must also be no significant imperfections in the permit market and markets relating to emitting activities.
 * Voluntary agreements: These are agreements between governments, often in the form of public agencies, and industry. Agreements may relate to general issues, such as research and development. In other cases they may involve quantitative targets. There is, however, the risk that participants in the agreement will free ride. They can do this by not complying with the agreement or by benefitting from the agreement while bearing no cost.
 * Creating helpful subsidies: Creating subsidies and financial incentives. One example is energy subsidies to support clean generation which is not yet commercially viable such as tidal power.

Carbon pricing
Imposing additional costs on greenhouse gas emissions can make fossil fuels less competitive and accelerate investments into low-carbon sources of energy. A growing number of countries raise a fixed carbon tax or participate in dynamic carbon emission trading (ETS) systems. In 2021, more than 21% of global greenhouse gas emissions were covered by a carbon price. This was a big increase from earlier due to the introduction of the Chinese national carbon trading scheme.

Trading schemes offer the possibility to limit emission allowances to certain reduction targets. However, an oversupply of allowances keeps most ETS at low price levels around $10 with a low impact. This includes the Chinese ETS which started with $7/t in 2021. One exception is the European Union Emission Trading Scheme where prices began to rise in 2018. They reached about €80/t in 2022. This results in additional costs of about €0.04/KWh for coal and €0.02/KWh for gas combustion for electricity, depending on the emission intensity.

Industries which have high energy requirements and high emissions often pay only very low energy taxes, or even none at all.

Methane emissions from fossil fuel extraction are occasionally taxed. But methane and nitrous oxide from agriculture are typically not subject to tax.

International agreements
Almost all countries are parties to the United Nations Framework Convention on Climate Change (UNFCCC). The ultimate objective of the UNFCCC is to stabilize atmospheric concentrations of greenhouse gases at a level that would prevent dangerous human interference with the climate system.

Although not designed for this purpose, the Montreal Protocol has benefited climate change mitigation efforts. The Montreal Protocol is an international treaty that has successfully reduced emissions of ozone-depleting substances such as CFCs. These are also greenhouse gases.

History
Historically efforts to deal with climate change have taken place at a multinational level. They involve attempts to reach a consensus decision at the United Nations, under the United Nations Framework Convention on Climate Change (UNFCCC). This is the dominant approach historically of engaging as many international governments as possible in taking action on a worldwide public issue. The Montreal Protocol in 1987 is a precedent that this approach can work. But some critics say the top-down framework of only utilizing the UNFCCC consensus approach is ineffective. They put forward counter-proposals of bottom-up governance. At this same time this would lessen the emphasis on the UNFCCC.

The Kyoto Protocol to the UNFCCC adopted in 1997 set out legally binding emission reduction commitments for the "Annex 1" countries. The Protocol defined three international policy instruments ("Flexibility Mechanisms") which could be used by the Annex 1 countries to meet their emission reduction commitments. According to Bashmakov, use of these instruments could significantly reduce the costs for Annex 1 countries in meeting their emission reduction commitments.

The Paris Agreement reached in 2015 succeeded the Kyoto Protocol which expired in 2020. Countries that ratified the Kyoto protocol committed to reduce their emissions of carbon dioxide and five other greenhouse gases, or engage in carbon emissions trading if they maintain or increase emissions of these gases.

In 2015, the UNFCCC's "structured expert dialogue" came to the conclusion that, "in some regions and vulnerable ecosystems, high risks are projected even for warming above 1.5 °C". Together with the strong diplomatic voice of the poorest countries and the island nations in the Pacific, this expert finding was the driving force leading to the decision of the 2015 Paris Climate Conference to lay down this 1.5 °C long-term target on top of the existing 2 °C goal.

Commitments to divest
More than 1000 organizations with investments worth US$8 trillion have made commitments to fossil fuel divestment. Socially responsible investing funds allow investors to invest in funds that meet high environmental, social and corporate governance (ESG) standards.

Barriers


There are individual, institutional and market barriers to achieving climate change mitigation. They differ for all the different mitigation options, regions and societies.

Difficulties with accounting for carbon dioxide removal can act as economic barriers. This would apply to BECCS (bioenergy with carbon capture and storage). The strategies that companies follow can act as a barrier. But they can also accelerate decarbonisation.

In order to decarbonise societies the state needs to play a predominant role. This is because it requires a massive coordination effort. This strong government role can only work well if there is social cohesion, political stability and trust.

For land-based mitigation options, finance is a major barrier. Other barriers are cultural values, governance, accountability and institutional capacity.

Developing countries face further barriers to mitigation.
 * The cost of capital increased in the early 2020s. A lack of available capital and finance is common in developing countries. Together with the absence of regulatory standards, this barrier supports the proliferation of inefficient equipment.
 * There are also financial and capacity barrier in many of these countries.

One study estimates that only 0.12% of all funding for climate-related research goes on the social science of climate change mitigation. Vastly more funding goes on natural science studies of climate change. Considerable sums also go on studies of the impact of climate change and adaptation to it.

Impacts of the COVID-19 pandemic
The COVID-19 pandemic led some governments to shift their focus away from climate action, at least temporarily. This obstacle to environmental policy efforts may have contributed to slowed investment in green energy technologies. The economic slowdown resulting from COVID-19 added to this effect.

In 2020, carbon dioxide emissions fell by 6.4% or 2.3 billion tonnes globally. Greenhouse gas emissions rebounded later in the pandemic as many countries began lifting restrictions. The direct impact of pandemic policies had a negligible long-term impact on climate change.

China
China has committed to peak emissions by 2030 and reach net zero by 2060. Warming cannot be limited to 1.5 °C if any coal plants in China (without carbon capture) operate after 2045. The Chinese national carbon trading scheme started in 2021.